Assessments - 2, GPA: 3.5
(
)
)
|
Facilidade de uso
Check their proper operation regularly. 2. Check bolts and screws for proper tightness at frequent intervals to keep the machine in safe working condition. Also, visually inspect machine for any damage and repair, if needed. 3. Before cleaning, repairing, or inspecting, stop the engine and make certain the impeller and all moving parts have stopped. Disconnect the spark plug wire and ground it against the engine to prevent unintended starting. 4. Do not change the engine governor settings or overspeed the engine. The governor controls the maximum safe operating speed of the engine. 5. Maintain or replace safety and instruction labels, as necessary. 6. Follow this manual for safe loading, unloading, transporting, and storage of this machine. 7. Never store the machine or fuel container inside where there is an open flame, spark or pilot light such as a water heater, furnace, clothes dryer, etc. 8. Always refer to the operator’s manual for proper instructions on off-season storage. 9. If the fuel tank has to be drained, do this outdoors. 10. Observe proper disposal laws and regulations for gas, oil, etc. to protect the environment. Your Responsibility Restrict the use of this power machine to persons who read, understand and follow the warnings and instructions in this manual and on the machine. NOTE: Not all safety labels shown may apply to your chipper shredder vacuum. 4 5 SECTION 2: ASSEMBLING YOUR CHIPPER SHREDDER VACUUM Unpacking • Remove staples, break glue on top flaps, or cut tape at carton end and peel along top flap to open carton. • Remove loose parts if included with unit (i.e., operator’s manual, etc.) • Cut along corners, lay carton down flat, and remove packing material. • Roll or slide unit out of carton and check carton thoroughly for loose parts. Loose Parts In Carton Following is the list of loose parts shipped with your equipment. Compare the parts with the illustration in Figure 1 to identify these items. 1. Nozzle 2. Bag 3. Chipper Chute 4. Tamper Plug 5. Oil (Not Shown) Figure 1 Before Assembly IMPORTANT: This unit is shipped without gasoline or oil in the engine. Be certain to service engine with gasoline and oil as instructed in the accompanying engine manual before operating your machine. NOTE: Reference to right or left side of the equipment is observed from the operating position, unless otherwise stated. • Before starting assembly, disconnect the spark plug wire from the spark plug on the chipper shredder vacuum and ground against the engine. Attaching The Nozzle • Remove three wing nuts from the front of the chipper shredder vacuum. • Place nozzle in position over the three studs on unit and secure with wing nuts just removed. See Figure 2. Figure 2 NOTE: The metal tab on the nozzle must depress the safety switch button attached to the front of the chipper shredder vacuum or the engine will not start. Attaching the Chipper Chute • Loosen, but do not remove, the two hex bolts, flat washers, and flange nuts which are secured to the support bracket. See Figure 3. Figure 3 • Remove the two flange nuts, hex bolts and saddle washers which secure the right side of the upper handle to the right side of the lower handle. See Figure 4. Nozzle Bag Chipper Chute Tamper Plug Wing Nuts Wing Nut Nozzle Chipper Chute Hex Bolts Flat Support Bracket Washers Flange Nuts 6 • Remove the three hex nuts and bell washers from the weld studs beside the opening on the right side of the chipper-shredder vacuum. See Figure 4. Figure 4 • Place the chipper chute over the weld studs keeping the slotted side towards the bottom. Loosely secure with the three hex nuts and bell washers that were removed earlier. Do not fully tighten the hex nuts at this point in the assembly. See Figure 5. Figure 5 • Align the support bracket with the holes in the right side of the upper and lower handles where the hex bolts were just removed. Push up slightly on the chipper chute in order to better align the holes in the support bracket with the holes in the handles. • Replace the hex bolts, saddle washers and flange nuts to affix the support bracket to the handle assemblies. See Figure 5. • Follow by tightening all hardware securely first on the chipper chute, then on the support bracket, and finally on the handle. Attaching The Bag • Place bag under the upper handle assembly and slip the front opening on the bag over the discharge chute, making certain it is over the rim on the discharge chute. Follow direction of the arrows in Figure 6. Figure 6 • Place the four straps on top of the bag over the upper handle, hooking them on the studs to secure in place. See Figure 6. Squeeze the clamp on the drawstring and pull the drawstring tight. Release the clamp. Hex Bolts & Saddle Washers Flange Nuts Weld Hex Nuts & Bell Washers Studs Flange Nuts Chipper Chute Hex Nuts & Slot Bell Washers Hex Bolts & Saddle Washers Support Bracket Bag Upper Handle Discharge Chute Strap Strap Strap 7 SECTION 3: KNOW YOUR CHIPPER SHREDDER VACUUM m Figure ...