Assessments - 3, GPA: 4
(
)
)
|
Facilidade de uso
Tools required: • 8mm open-end wrench • 9mm open-end wrench • 10mm open-end wrench • 12mm open-end wrench • 13mm open-end wrench • Phillips screw driver • 5/8” open end wrench • 3/4” open end wrench • Needle nose pliers • Soap and water solution (to check for leaks) DANGERS and Cautions 1. Installation and repair should be done by a qualified service person. 2. Use only Blue Rhino Global Sourcing, LLC. factory authorized parts. The use of any part that is not factory authorized can be dangerous. This will also void your warranty. Contact 1.800.762.1142. 3. Do not use flammable solutions or material to clean heater or heater parts. Use only warm soapy water to clean outside of heater. 4. Do not submerge control valve in water. Cleaning burner, pilot replacement and valve change. Model No. 233010 Natural Gas 501310 ®® For assistance call 1.800.762.1142. Steps 1-4 1. Turn gas supply off and disconnect from gas supply. Important: make sure your gas supply is off. 2. Remove dome. 3. Remove engine from post. Cleaning burner, pilot replacement and valve change. Model No. 233010 Natural Gas 501310 ®® For assistance call 1.800.762.1142. Step 5 Remove the three bolts which secure the emitter to the emitter bottom using a 9mm wrench. Cleaning burner, pilot replacement and valve change. Model No. 233010 Natural Gas 501310 ®® For assistance call 1.800.762.1142. Step 6 1. Clean the carbon build-up off the inside of the emitter bottom with a non-abrasive scouring pad or bottle brush. Clean the outside of the emitter bottom with the scouring pad. 2. Use the air compressor to blow away any excess soot. DANGER: Never use any flammable solutions or material to clean heater or heater parts. Use only a mild soap and water solution. Do not to soak the valve. Cleaning burner, pilot replacement and valve change. Model No. 233010 Natural Gas 501310 ® For assistance call 1.800.762.1142. Step 7Disconnect the pilot supply tube using #10 open-ended wrench. ® For assistance call 1.800.762.1142. Step 7Disconnect the pilot supply tube using #10 open-ended wrench. Cleaning burner, pilot replacement and valve change. Model No. 233010 Natural Gas 501310 ® For assistance call 1.800.762.1142. Cleaning burner, pilot replacement and valve change. Model No. 233010 Natural Gas 501310 Step 8Disconnect the burner supply tube from the control valve using 5/8” open-ended wrench. ®® For assistance call 1.800.762.1142. Step 9 1. Disconnect the burner from the emitter bottom by removing the 2 phillips screws on the bottom of the emitter bottom. 2. Carefully remove the burner. Cleaning burner, pilot replacement and valve change. Model No. 233010 Natural Gas 501310 ® For assistance call 1.800.762.1142. Step 10Disconnect the thermal couple wire from the control valve: 1. Remove the screw that holds the access panel to the housing. 2. Remove the nut from the back of the control valve using 8 mm open-ended wrench. Note: Be very careful not to damage any wires. ® For assistance call 1.800.762.1142. Step 10Disconnect the thermal couple wire from the control valve: 1. Remove the screw that holds the access panel to the housing. 2. Remove the nut from the back of the control valve using 8 mm open-ended wrench. Note: Be very careful not to damage any wires. Cleaning burner, pilot replacement and valve change. Model No. 233010 Natural Gas 501310 ® For assistance call 1.800.762.1142. Step 11Remove the heat and pilot shield from the emitter bottom. ® For assistance call 1.800.762.1142. Step 11Remove the heat and pilot shield from the emitter bottom. 1. Remove the 4 screws in emitter bottom. Note: 2 screws are near pilot opening, and 2 screws are on the back side of the emitter bottom. 2. Lift the heat shield assembly out. Note: Be very careful not to damage any wires. Cleaning burner, pilot replacement and valve change. Model No. 233010 Natural Gas 501310 ®® For assistance call 1.800.762.1142. Step 121. Remove the pilot assembly by removing the 2 screws that hold the pilot assembly in placeNote: you may need to use a pair of needle nose pliers to hold the nuts in place. 2. If replacing the pilot: A. Remove the ignitor wire, by carefully bending the fork on the retaining bracket up using need nose pliers B. Pull down on the ceramic tube C. Disconnect the igniter wire from the pilot. D. Replace the old pilot with the new pilot, re-attch the ignitor wire, slide the ceramic tube back up, and bend the fork to the proper place. 3. Reattach the pilot assembly. Cleaning burner, pilot replacement and valve change. Model No. 233010 Natural Gas 501310 ®® For assistance call 1.800.762.1142. Step 13 1. Remove the orifice by placing the 12 mm open-ended on the pilot orifice and the 10 mm open-ended on the hex tube just below the pilot hood. 2. Use a pipe cleaner to clean both the inside and outside of the pilot orifice. 3. With a brush, lightly clean the top of the pilot orifice. Use care not to enlarge the orifice hole. Cleaning burner, pilot replacement and valve change. Model N...