Assessments - 3, GPA: 3.3
(
)
)
|
Facilidade de uso
Do not let water run down through openings (B) in the top of the door. To help prevent water from getting in these slots when cleaning, open the door as far as it will go. Do not rub or clean the door gasket (C)— the fiberglass material of the gasket has an extremely low resistance to abrasion. An intact and well-fitting oven door gasket is essential for energy-efficient oven operation and good baking results. If you notice the gasket becoming worn, frayed or damaged in any way or if it has become displaced on the door, you should have it replaced. 4. Close the door and make sure the oven light (D) is off. Make sure the oven light bulb cover is in place. Door latches automatically after the Clean cycle is set. Oven shelves may be cleaned in the self-cleaning oven. However, they will darken, lose their luster and become hard to slide. Wipe the shelf supports with cooking oil after self-cleaning to make the shelves slide more easily. Do not use commercial oven cleaners or oven protectors in or near the self-cleaning oven. A combination of any of these products plus the high clean cycle temperatures may damage the porcelain finish of the oven. Important The oven door must be closed and dl controls must be set correctly for the clean cycle to work properly. How to Set Oven for Cleaning Quick Reminder: 1. Prepare the oven for cleaning. 2. Close the oven door completely. 3. Press the CLEAN pad. 4. Press the INCREASE or DECREASE pad until desired Clean Time appears. If the oven is too hot and you start to set a clean cycle, the word “OFF” will appear in the display. Allow additional time for cooling before you try to set the cycle. 1. Follow directions to prepare the oven for cleaning. 12. Press the CLEAN pad. I CLEAN I [ ~1 3. Press the INCREASE or DECREASE pad until desired Clean Time is displayed. Clean Time is normally 3 hours. You can change the Clean Time to anywhere between 2 and 4 hours, depending on how dirty your oven is. The self-clean cycle will automatically begin after “CLEAN” is displayed and the time for the clean cycle is set. The word “ON” will appear on the display. When the oven heats up the word “LOCK” will be displayed and the door will lock automatically. It will not be possible to open the oven door until the temperature drops below the lock temperature and the LOCK light goes off. 4. When the LOCK light is off, open the door. NOTE: YoL~ can find out when the STOP clean cycle will be finished by pressing the STOP TIME button. TIME m II The word “door” will be displayed, the word “LOCK” will flash and oven control will signal if you set the clean cycle and forget to close the oven door. To Stop a Clean Cycle m CLEAR OFF 1. Press the CLEAWOFF pad. 2. Wait until the oven has cooled below locking temperature. You will not be able to open the door right away unless the oven temperature is at a safe level. (continued next page) OPEMT~G T~ SELF-CLEANmG OWN (continued) After Self-Cleaning You may notice some white ash in the oven. Just wipe it up with a damp cloth after the oven cools. If white spots remain, remove them with a soap-filled steel wool pad. Be sure to rinse thoroughly with a vinegar and water mixture. These deposits are usually a sdt residue that cannot be removed by the clean cycle. If the oven is not clean after one clean cycle, repeat the cycle. NOTE: No functions can be programmed before the door automatically unlocks. How to Set Delay Start of Cleaning Quick Reminder: 1. Prepare the oven for cleaning. 2. Close the oven door completely. 3. Press the CLEAN pad. 4. Press the INCREASE or DECREASE pad until desired Clean Time appears. 5. Press the STOP TIME pad. 6. Press the INCREASE or DECREASE pad until desired Stop Time appears in the display. Delay Start is setting the oven timer to start the clean cycle automatically ‘at a later time than the present time of day. NOTE: Before beginning, make sure the oven clock shows the correct time of day. 1. Follow steps to prepare the oven for cleaning. 2. Press the CLEAN pad. CLEAN m I I n n A A 3. Press the INCREASE or DECREASE pad to enter Clean Time. 1 1 m m 4. Press the STOP TIME pad. STOP “SET STOP TIME” and the earliest Stop Time you can set will TIME appear on display. The earliest Stop Time will be the Clean Time selected plus the time of day. For example: If the Clean Time is three hours and the time of day is 6:00, the Stop Time that appears on the display will be 9:00. 5. Press the INCREASE pad to change the Stop Time to a later time of day if desired. For example: If you set Stop Time at 11:00, oven will start clean cycle at 8:00 and end at 11:00. The door latches automatically. The self-clean cycle will automatically begin after “CLEAN” is displayed and the time for clean cycle is set. The word “ON” will appear on the display. When the oven heats up, the word “LOCK” will be displayed and the door will lock automatically. It will not be possible to open the oven door until the temperature drops below the lock temperature and the ...
Este manual também é adequado para os modelos :Fornos Elétricos - ZEK736GP (695.38 kb)
Fornos Elétricos - ZEK73WP (695.38 kb)
Fornos Elétricos - ZEK736GP (695.38 kb)