Assessments - 3, GPA: 4.7
(
)
)
|
Facilidade de uso
Warning Your shaving system is provided with a special cord set, which has an integrated Safety Extra Low Voltage power supply. Do not exchange or tamper with any part of it, otherwise there is risk of an electric shock. This appliance is not intended for use by children or persons with reduced physical or mental capabilities, unless they are supervised by a person responsible for their safety. In general, we recommend that you keep the appliance out of reach of children. To prevent the cleaning fluid from leaking, ensure that the Clean&Renew station is placed on a fl at surface. When a cleaning cartridge is installed, do not tip, move suddenly or transport the station in any way as cleaning fluid might spill out of the cartridge. Do not place the station inside a mirror cabinet, nor over a radiator, nor place it on a polished or lacquered surface. The cleaning cartridge contains a highly flammable liquid so keep it away from sources of ignition. Do not smoke near the station. Do not expose to direct sunlight for long periods of time. Do not refill the cartridge and use only original Braun refi ll cartridges. Description Clean&Renew station 1 Cleaning fl uid display 2 Lift button for cartridge exchange 3 Station-to-shaver contacts 4 «start cleaning» button 5 Cleaning program indicators 6 Station power socket 7 Cleaning cartridge Shaver 8 Foil & Cutter cassette 9 Cassette release button 0 Shaver head «lock» switch q Pop-out long hair trimmer 13 w On/off switch e «sensitive» (–) setting button r «intensive» (+) setting button t Reset button z Shaver display u Shaver-to-station contacts i Shaver power socket o Travel case p Special cord set Before shaving Prior to fi rst use you must connect the shaver to an electrical outlet using the special cord set p or alternatively proceed as below. Installing the Clean&Renew station • Using the special cord set p, connect the station power socket 6 to an electrical outlet. • Press the lift button 2 to open the housing. • Hold the cleaning cartridge 7 down on a fl at, stable surface (e.g. table). • Carefully remove the lid from the cartridge. • Slide the cartridge into the base of the station as far as it will go. • Slowly close the housing by pushing it down until it locks. The cleaning fl uid display 1 will show how much fl uid is in the cartridge: «high» up to 30 cleaning cycles available «low» up to 7 cleaning cycles remaining «empty» new cartridge required Charging and cleaning the shaver Insert the shaver head down into the cleaning station. (The contacts u on the back of the shaver will align with the contacts 3 in the cleaning station). If required, the Clean&Renew station will automatically charge the shaver. The hygiene status of the shaver will also be analyzed and one of the following cleaning program indicators 5 will light up: new fastclean high low empty startcleaning fastclean high low empty startcleaning fastclean high low empty startcleaning 2 1 clean clean clean clean high low empty high low empty high low empty high clean low empty startcleaning trimmer reset Series 7 14 lcleanstart cleaning tleanihigh clean low startcleaning lcleanstart cleaning 100 7550 25 lowcharge 100 7550 25 lowcharge 14 lcleanstart cleaning tleanihigh clean low startcleaning lcleanstart cleaning 100 7550 25 lowcharge 100 7550 25 lowcharge «clean» shaver is clean « » short economical cleaning required « » normal level of cleaning required « » high intensive cleaning required If the station selects one of the required cleaning programs, it will not start unless you press the «start cleaning» button 4. For best shaving results, we recommend cleaning after each shave. Whilst cleaning is in progress, the respective cleaning program indicator will blink. Each cleaning program consists of several cycles, where cleaning fluid is flushed through the shaver head and a heat drying process dries the shaver. Depending on the program selected the total cleaning time will range from 32 to 43 minutes. The cleaning programs should not be interrupted. Please note that whilst the shaver is drying, the shaving head may be hot and wet. When the program is finished, the blue «clean» indicator will light up. Your shaver is now clean and ready for use. Stand-by mode 10 minutes after completing the charging or cleaning session, the Clean&Renew station switches to the stand-by mode: The indicators of the Clean&Renew station turn off. Shaver display The shaver display z shows the charge status of the battery. During charging or when using the shaver, the respective green charge status will blink. When the battery is fully charged the green charge status will light up continously, provided the shaver is switched on or connected to an electrical outlet. Low charge indicator: The red «low» charge indicator blinks to indicate that the charge has dropped below 20%, provided the shaver is switched on. The remaining battery capacity is sufficient for 2 to 3 shaves. Charging information • A full charge provides u...