Assessments - 0, GPA: 0
(
)
)
|
Facilidade de uso
Gently press the base of the razor towards the back of the Jet Clean System so that the razor base fits snugly in place. Lock the razor into place by pushing the lever down completely. The charging light will blink to indicate the razor automatically begins to charge. 5 Press the ON/OFF button to start the cleaning cycle. The cleaning light on the Jet Clean System star ts blinking and the razor is automatically lowered into the cleaning solution. The razor stops charging while it is cleaning. . During the first phase of the cleaning cycle, the razor will automatically turn on and off several times while the razor holder lowers and raises the razor’s position in the cleaning solution, removing all debris. The cleaning light will blink continuously. . During the second phase of the cleaning cycle, the razor holder moves the razor to the drying position and the cleaning light will light up continuously. 24 ENGLISH C C . Do not lift the razor lever or press the ON/OFF button while the cleaning cycle is running. If this does occur, the cleaning cycle will stop and the razor holder will automatically move to the starting position. The cleaning cycle can be re-started by pressing the ON/OFF button once. . If the power plug is disconnected before the cleaning cycle is complete, the razor holder will remain in its current position. Reconnect the plug into the outlet or Jet Clean System and the razor holder will automatically move to the highest position. The cleaning cycle can be re-started by pressing the ON/OFF button once. NOTE: If the cleaning solution level drops below the minimum level during the cleaning cycle, the cleaning light will blink at intervals and razor holder returns the razor to the starting position, stopping the cleaning cycle. Unplug Jet Clean System from the outlet, remove razor and refill canister (see “Preparing Jet Clean system for Use”). 6 When the entire cleaning cycle is complete and the razor is hygienically clean, the razor will be raised to the starting position and the charge light on the Jet Clean System will blink indicating that the razor is (re)charging. 7 Raise the lever holding the razor to the highest position (1) and carefully remove the razor from the Jet Clean System (2). ENGLISH 25 . You may quickly rinse the razor heads with warm water after using the Jet Clean System to remove any residual cleaning solution. . If the razor needs to be recharged, you can simply leave it in the Jet Clean System after cleaning and the razor will automatically recharge. The charge light on the Jet Clean System will blink to indicate the razor is recharging. . For optimal razor drying time after cleaning, remove razor from Jet Clean System after the cleaning cycle is complete and allow to air dry. . You may store your razor in the Jet Clean System. Unplug from the outlet when charging/cleaning is complete. Quick Cleaning: Razor Heads The razor heads may also be quickly cleaned after each use by rinsing with hot water. Water from the tap should be on a hot setting, BUT BE CAREFUL TO TEST WATER FIRST SO AS NOT TO BURN OR SCALD HANDS. . Regular cleaning guarantees better shaving results. . Do not immerse razor in water. C . The tap symbol on the back of the razor indicates that the razor can be rinsed under running tap water. C . While rinsing razor heads, water may drip out of the base of razor. This is a normal occurrence. 26 ENGLISH C C C C 1 Always turn razor OFF, unplug from outlet and remove cord from razor before cleaning. 2 Press the Razor Head Release Button, flip open the Razor Head Assembly. 3 Clean inside razor heads and hair chamber by running under hot water. 4 5 6 Clean outside of Razor Head Assembly by running under hot water. Close the Razor Head Assembly and shake off excess water. Open Razor Head assembly again and leave open to air dry. NOTE: Do not wipe or dry the shaving heads with a towel or tissue. This could damage the shaving heads. C C C ENGLISH 27 7 8 If the shaving unit becomes detached from the razor, you can easily reattach it. You may also clean the hair chamber without water by using the supplied brush. After Each Use: Trimmer Turn razor OFF. Push down spring-release trimmer switch. Clean trimmer with the brush every time you use it. Lubricate the trimmer teeth with Philips Norelco Razor Lubricant (model AL80) or with one drop of mineral oil every 6 months. Close trimmer by pressing trimmer down. 1 2 3 4 5 This razor and Jet Clean System have no other userserviceable parts. Any other service should be performed by the Philips Norelco Service Location. Cleaning the Jet Clean Canister For optimal performance of the Jet Clean System, it is recommended that you empty the cleaning solution canister and thoroughly rinse the canister clean every 2 weeks. 1 Place the Jet Clean System on a flat, level surface. 28 ENGLISH C C C C 2 Simultaneously press the buttons located on both sides of the Jet Clean System (1) and lift the appliance off the Jet Clean canister (2) . Alwa...