Assessments - 0, GPA: 0
(
)
)
|
Facilidade de uso
This product used to be called Action Clean. Preparing the Philips shaving head Cleaner for use The Philips Shaving Head Cleaner can be used to clean shavers with two and three shaving heads. 1 2 3 Turn the top of the Philips Shaving Head Cleaner anticlockwise (1) and pull it from the base (2). (Fig. 1) Remove the filter unit from the base. (Fig. 2) 4 ,,,, , Place the appropriate shaving unit holder onto the filter unit.Theappropriate shaving units for the different shaver series are shown inthe pictures below. Suitable for Sensotec shavers (HQ8000 series). (Fig. 3) Suitable for Quadra shavers (HQ7000/6000 series). (Fig. 4) Suitable for all other 3-head shavers, except type HQ9. (Fig. 5) Suitable for Quadra Action shavers (HQ600 series). (Fig. 6) Suitable for all other 2-head shavers, except type HS190. (Fig. 7) Make sure the lugs on the holder fit into the slots of the filter unit. (Fig. 8) 5 Empty the contents of the bottle of cleaning fluid into the base. (Fig. 9) Be careful not to spill cleaning fluid onto polished surfaces, such as bathroom worktops, as they may become blotched and dull as a result. Using the Philips shaving head Cleaner Clean the shaving unit with the Philips Shaving Head Cleaner once a month. 1 Fit the shaving unit onto the holder. (Fig. 10) hQ8000 series only: Slide the spring of the HQ8000 shaving unit into the recess of the , shaving unit holder. (Fig. 11) Make sure the spring remains properly in place in the recess when you close the shaving unit. Close the shaving unit by pushing it carefully down onto the holder. , (Fig. 12) 2 Place the top of the Philips Shaving Head Cleaner on the base (1) andturn it clockwise until you hear a click (2). (Fig. 13) 3 Pump the cleaning fluid through the shaving unit by pushing the top of the Philips Shaving Head Cleaner down 30 times. (Fig. 14) 4 When you are finished, remove the top from the base and removethe shaving unit from the holder. (Fig. 15) Place the shaving unit on a piece of kitchen towel or tissue and allow it to dr y. 5 Do not rinse the shaving unit with water. (Fig. 16) Note:The Sensotec (HQ8000 series), Quadra (HQ7000/6000 series) and Quadra Action (HQ600 series) shavers are watertight and can be cleaned under the tap. Be careful with hot water. Always check if the water is not too hot toprevent your hands from getting burnt. 6 Place the top of the Philips Shaving Head Cleaner on the base (1) and turn it clockwise until you hear a click (2). (Fig. 13) You can clean the shaving unit every month with the same cleaning , fluid for a whole year. Replacing the filter and the cleaning fluid Only use Philips Shaving Head Cleaning Fluid HQ101, which includes a bottle of cleaning fluid and a filter.The Philips Shaving Head Cleaning Fluid HQ101 can be obtained from your Philips dealer. 1 Remove the filter unit. (Fig. 17) 2 Remove the old filter from the filter unit. (Fig. 18) 3 Place a new filter in the filter unit. (Fig. 19) 4 Pour the used cleaning fluid into a bottle (for more information on disposal of the fluid, see chapter ‘Environment’). (Fig. 20) 5 Place the filter unit in the base. (Fig. 21) 6 Fill the base of the Philips Shaving Head Cleaner with new cleaning fluid. (Fig. 22) environment Do not pour old cleaning fluid down the sink, but pour it in a bottle , and hand it in at an official collection point for chemical waste. By doing this you will help to preserve the environment. (Fig. 23) 4222001825478 DeUtsCh einfuhrung Der Philips Shaving Head Cleaner reinigt die Scherkopfe Ihres Rasierers grundlich und sorgt fur eine gute Rasur. Dieses Gerat trug fruher die Bezeichnung Action Clean. Den Philips shaving head Cleaner fur den gebrauch vorbereiten Der Philips Shaving Head Cleaner eignet sich zur Reinigung von Rasierern mit zwei oder drei Scherkopfen. 1 2 3 Drehen Sie die Kappe des Gerats gegen den Uhrzeigersinn (1) vonder Basis ab (2). (Abb. 1) Nehmen Sie die Filtereinheit aus der Basis. (Abb. 2) Setzen Sie den Halter fur die betreffende Schereinheit auf die ,, , ,, Filtereinheit. Die passenden Schereinheiten fur die verschiedenen Rasiererserien sind in den untenstehenden Abbildungen dargestellt. Fur Sensotec (Serie HQ8000). (Abb. 3) Fur Quadra (Serie HQ7000/6000). (Abb. 4) Fur alle anderen Rasierer mit drei Scherkopfen (au.er Typ HQ9). (Abb. 5) Fur Quadra Action (Serie HQ600). (Abb. 6) Fur alle anderen Rasierer mit zwei Scherkopfen (au.er Typ HS190). (Abb. 7) 4 Achten Sie darauf, dass die Vorsprunge auf dem Halter in die Schlitzeder Filtereinheit eingreifen. (Abb. 8) 5 Fullen Sie den Inhalt der Flasche mit Reinigungsflussigkeit in die Basis des Gerats. (Abb. 9) Achten Sie darauf, dass keine Spritzer der Reinigungsflussigkeit aufpolierte Flachen geraten, wie sie in Badezimmern zu finden sind. Es konnten Flecken und matte Stellen entstehen. Den Philips shaving head Cleaner verwenden Reinigen Sie die Schereinheit einmal monatlich mit dem Philips Shaving Head Cleaner. 1 Setzen Sie die Schereinheit auf den Halter. (Abb. 10) nur seri...