Assessments - 4, GPA: 3.8
(
)
)
|
Facilidade de uso
Andis will not be liable for any consequential damages resulting from any defect in material or workmanship of any of its products. Some States do not allow limitations on how long an implied warranty lasts or exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you. The Warranty gives you specific legal rights, and you may also have other rights which may vary from State to State. Date Purchased______________________________________ Model____________________________ ANDIS AUTHORIZED REPAIR SERVICE STATIONS Please refer to the service stations listing on web site for most up-to-date Listings ! Thanks KEEP THIS FOR YOUR RECORDS Form # 22311 Rev. A ©2001 Andis Company, USA Printed in U.S.A. MODEL BGC Clipper DIAGRAM G DIAGRAM H DIAGRAM H DIAGRAM M DIAGRAM I DIAGRAM K DIAGRAM L DIAGRAM J IMPOR T ANT SAFEGUARD S When using should always Read all instructions Andis Clipper. DANGER: To reduce the risk of electric 1. Do not reach for an appliance into water. Unplug immediately. 2. Do not use while bathing or in a 3. Do not place or store appliance where fall or be pulled into a tub or sink. Do in or drop into water or other liquid. 4. Always unplug this appliance from the electrical outlet immediately after using. 5. Unplug this appliance before cleaning, removing, or assembling parts. WARNING: To reduce the risk of burns, fire, electric shock, or injury to persons: 1. An appliance should never be left unattended when plugged in. 2. Close supervision is necessary when this appliance is used by, on, or near children or invalids. 3. Use this appliance only for its intended use as described in this manual. Do not use attachments not recommended by Andis. 4. Never operate this appliance if it has a damaged cord or plug, if it is not working properly, if it has been dropped or damaged, or dropped into water. Return the appliance to an Andis Service Center for examination and repair. 5. Keep the cord away from heated surfaces. 6. Never drop or insert any object into any opening. 7. Do not use outdoors or operate where aerosol (spray) products are being used or where oxygen is being administered. 8. Do not use this appliance with a damaged comb or broken blade, as injury to the skin may occur. 9. To disconnect turn control to “ off” then remove plug from outlet. SAVE THESE INSTRUCTIONS SERVICING A DOUBLE-CLIPPER In a double-two systems are provided is provided on a nor should a means for grounding clipper requires system, and should be Andis Authorized Service Station. Replacement those parts being replaced. A double-insulated clipper is marked by the words “ DOUBLE INSULATION” or “ DOU BLE INSULATED” . The symbol may also be marked on the appliance. OPERATING INSTRUCTIONS Please read the following instructions before using your new Andis Clipper. Give it the care that a fine precision built instrument deserves and it will give you years of service. Plug cord into electrical outlet, operate 120 volt, 60 cycle AC electrical current or as noted on unit. To start clipper move switch button to the # 1 position. To stop, move switch button back to original position. REMOVING BLADE SET To remove blade set, first make sure your clipper motor is switched “ OFF” , then push down on blade with one or both thumbs (Diagram A) and slide blade off blade hinge. If your blade hinge should snap closed and is flush with the clipper, use a small standard screwdriver to pry the tongue of the hinge out (Diagram B). NOTE: Hair may accumulate in the front cavity of the housing under the blade. If this happens, you can clean out the hair by brushing out the cavity with a small brush or an old toothbrush while the blade is off the clipper (See Diagram C for location of cavity being referenced). DIAGRAM A DIAGRAM B DIAGRAM C DIAGRAM D REPLACING OR CHANGING To replace or change your blade set, bracket onto the hinge of the clipper and with the clipper turned “ON” , push the blade towards the clipper to lock into position. USER MAINTENANCE The internal mechanism of your motor clipper has been permanently lubricated by the factory. Other than the recommended maintenance described in this manual, no other maintenance should be performed, except by Andis Company, or an Andis Authorized Repair Service Station. This Product intended for Professional Use CARE AND SERVICING OF YOUR ANDIS CLIPPER BLADES Blades should be oiled before, during, and after each use. If your clipper blades leave streaks or slow down, it’s a sure sign blades need oil. Place a few drops of oil on the front and side of the cutter blades (Diagram E). Wipe excess oil off blades with a soft, dry cloth. Spray lubricants contain insufficient oil for good lubrication, but are an excellent clipper blade coolant. Always replace broken or nicked blades to prevent injury. You can clean the excess hair from your blades by using a small brush or worn out toothbrush. To clean the blades, we suggest to immerse the blades only int...