Please note that whilst the shaver is drying, the shaving head may be hot and wet. When the program is finished, the blue «clean» diode will light up. Your shaver is now clean and ready for use. Fast cleaning Push the «fast clean» button © to activate the fast clean program without drying. This program takes about 25 seconds only and is recommended when you do not have time to wait for one of the automatic cleaning programs. If you remove the shaver just after the program has finished, wipe of

We hope you enjoy your new Braun Shaver. Warning Your Pulsonic shaving system is provided with a special cord set, which has an integrated Safety Extra Low Voltage power supply. Do not exchange or tamper with any part of it, otherwise there is risk of an electric shock. To prevent the cleaning fluid from leaking, ensure that the Clean&Renew station is placed on a flat surface. When a cleaning cartridge is installed, do not tip, move suddenly or transport the station in any way as cleaning flu

August 2005 8:42 08 4. Remaining shaving time / Shaver must be charged. 5. Time left in the cleaning process. 6. To maintain 100% shaving performance, replace your foil and cutter block, when the display shows «replace foil» (after about 18 months) or when the shaving parts are worn. Change both parts at the same time for a closer shave with less skin irritation. (Shaver foil (10) and cutter block (11): 8000 series) The display will keep on reminding you during the next 7 days to replace the

When fully charged, the charging light flashes or goes off. If later on, the charging light comes on again, this indicates that the shaver is being recharged to maintain its full capacity. Charging information A full charge will give up to 50 minutes of cordless shaving time, depending on your beard growth. Best environmental temperature range for charging is 15 °C to 35 °C. For battery maintenance, the system will automatically initiate full discharging and then recharging of the batteries.

when travelling. Never use water to clean the shaver. Remove the shaver foil and tap it out on a flat surface. Using the brush, clean the inner area of the pivoting head. However, do not clean the shaver foil nor the cutter block with the brush as this may damage them. If you do not use the Clean&Renew™ station for a longer period of time, you should apply a drop of light machine oil onto the shaver foil. Cleaning the housing Clean the housing of shaver and station from time to time with a

Each cleaning consists of several cycles (where the cleaning fluid is flushed through the shaver head) and a heat drying period. The total cleaning time is 33 to 50 minutes. Cleaning processes in the Clean&Charge should not be interrupted. While the shaver is drying, the metal parts of the shaver may be hot. Also, if the shaver is taken out prematurely and is not dry, its electronics could be harmed. When the program is finished, the blue «clean» light will shine. You can release the shaver by

Insert the shaver head down into the station (the contacts on the back of the shaver (14) will correspond to the contacts in the station (3)). If necessary, the system will now charge the shaver. Also, the cleaning status will be automatically analyzed and one of the four diodes of the cleaning program display (5) will light up: a) The shaver is clean b) Eco(nomic), i.e. short cleaning required c) Normal cleaning required d) Intensive cleaning required If the system has selected one of the

It ensures unsurpassed closeness and comfort for you and optimum care for your shaver: • The system automatically adapts to any voltage worldwide. • The system recognizes when cleaning of your shaver is required, and automatically recognizes which of the three cleaning programs is appropriate. • While the shaver is connected to the mains, the system automatically takes care of charging and discharging in a way that is optimized for the shaver’s battery capacity and life span. • The system ta

Le rasoir doit être éteint. Laissez-le se charger pendant au moins 4 heures (le cordon d’alimentation et rasoir peuvent devenir tiède). Quand le rasoir est complètement chargé, vous pouvez vous raser sans le fil, jusqu’à ce qu’il soit complètement déchargé. Ensuite rechargez-le à nouveau pour atteindre sa pleine capacité (1 heure). • Une pleine charge procurera environ 50 minutes de rasage sans fil en fonction du type de barbe. Cependant la capacité maximale des batteries sera atteinte seulemen

Wir wünschen Ihnen mit Ihrem Braun Rasierer viel Freude. Das System zeigt Ihnen an, wann Scherfolie und Klingenblock erneuert werden müssen. Achtung Das Gerät trocken halten. Ihr Rasierer ist mit einem Spezialkabel mit integriertem Netzteil für Keinschutz-spannung ausgestattet. Es dürfen keine Teile ausgetauscht oder Veränderungen vorgenommen werden, da sonst Stromschlaggefahr besteht. Beschreibung 1 Schutzkappe 2 Scherfolie 3 Klingenblock 4 Entriegelungstasten 5 Langhaarschneider 6 Sc