Assessments - 3, GPA: 3.7
(
)
)
|
Facilidade de uso
(See Figure C.) 4. Check the Fuel Gauge (34) for the amount of unleaded gasoline in the Fuel Tank (32). If necessary, remove the Fuel Tank Cap (37) and refill the Fuel Tank with unleaded gasoline. Then, replace the Fuel Tank Cap. (See Figure D.) FIGURE C OIL FILL CAP FUEL GAUGE (34) FUEL TANK CAP (37) FUEL TANK (32) FIGURE D REV 11/04 SKU 90236 For technical questions, please call 1-800-444-3353. Page 13 To StartThe Generator: To StartThe Generator: . Turn the Fuel Valve (31) to its vertical “OPEN” position. (See Figure E.) 2. Move the Engine’s Fuel Choke all the way to the right to its “START” position. (See Figure E.) 3. Turn the Engine’s “ON/OFF” Switch (46) to its “ON” position (See Figure F.) 4. Grasp the Handle of the Engine’s Starter Pulley and rapidly pull the FIGURE E Starter Pulley to start the Engine. NOTE: It may take more than one pull on the Starter Pulley to start the Engine. 5. Allow the Engine to run for several seconds, then move the Engine’s Fuel Choke all the way to the left to its “RUN” position. (See Figure E.) NOTE: DO NOT ATTEMPT TO ADJUST THE ENGINE’S THROTTLE! This engine uses a governor device to automatically control the engine’s speed. If the throttle is adjusted, it may result in decreased efficiency and/or damage to the unit. CHOKE FUEL VALVE (31) Hidden from view ON/OFF Switch FIGURE F 120/240 V OVERLOAD BREAKERS 120V DUAL OUTLET TWISTLOCK OUTLET GROUNDING POINT (42) (43) (44) FIGURE G REV 06/04; 11/04 SKU 90236 For technical questions, please call 1-800-444-3353. Page 14 PoweringTools And Equipment: PoweringTools And Equipment: . Prior to powering tools and equipment, make sure the Generator’s rated voltage, wattage, and amperage capacity (120V/ 15 AMP and 240V/ 15 AMP) is adequate to supply all electrical loads that the unit will power. If powering exceeds the Generator’s capacity, it may be necessary to group one or more of the tools and/or equipment for connection to a separate Generator. 2. Once the Generator is running, simply connect the Power Cords of 120 volt powered tools and equipment into the 120 volt Dual Outlets (41). If a 240 volt tool or equipment is used, connect its power cord into the 240 volt Twistlock Outlet (42). (See Figure H.) 3. NOTE: The Generator features twoAC Non-Fuse Overload Breakers (40) to protect the AC circuit in case of an overload. Should an overload occur one or both of the Breakers will “trip”, interrupting the circuit (disconnecting power to the connected tools and/or equipment). In this case, refer to Step #1 in this section. Then, reset the circuitry system by depressing the Breaker(s). Restart the Generator and continue powering the remaining tools and equipment. (See Figure H.) AC CIRCUIT OVERLOAD BREAKER (40) 120V DUAL OUTLET (41) 120/240V TWISTLOCK OUTLET (42) FIGURE H 4. When finished using the Generator, turn the ON/OFF switch on the engine’s fan shroud to its “OFF” position to stop the Generator. (See Figure G.) 5. After the Engine and Generator have completely cooled, disconnect the spark plug wire and store the Generator in a safe, clean, dry location (if not already installed in one). REV 06/04 SKU 90236 For technical questions, please call 1-800-444-3353. Page 15 INSPECTION, MAINTENANCE, AND CLEANING 1. NOTE: Preventative maintenance procedures and frequency will vary depending on the amount of Generator use. Refer to the Engine manufacturer’s Operation, Maintenance, and Parts manual (included) for detailed information regarding maintenance of the Engine. 2. CAUTION! Always make sure the ON/OFF Switch is in its OFF position. Disconnect the spark plug wire from the engine. And allow sufficient time for the Engine and Generator to completely cool before performing any inspection, maintenance, or cleaning. 3. BEFORE EACH USE, inspect the general condition of the Generator. Check for loose screws, misalignment or binding of moving parts, cracked or broken parts, damaged electrical wiring, and any other condition that may affect its safe operation. If abnormal noise or vibration occurs, have the problem corrected before further use. Do not use damaged equipment. 4. BEFORE EACH USE, check to make sure the Engine’s oil level is adequate. Refer to the Engine manufacturer’s Operation, Maintenance, and Parts Manual (included) for specific information. 5. DAILY: With a soft brush, cloth, or vacuum, remove all debris from the Generator. Then, use a premium quality, lightweight machine oil to lubricate all moving parts. PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/ OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CER...