Assessments - 2, GPA: 4.5
(
)
)
|
Facilidade de uso
FILTER OIL 67 0C1852 1 ADAPTER DRAIN OIL 68 0912970066 1 GROUND WIRE (STARTER) 69 070928 1 CLAMP HOSE - OIL DRAIN 70 069860C 1 HOSE OIL DRAIN ASSY 21" 71 035473 1 CLAMP HOSE #12 .50-1.25 72 077996 1 CAP ANTIFREEZE RUBBER 73 069811 1 CAP HEX 1/4 NPT BRASS 74 ** 0A1354A 1 REGULATOR - DC ALT 75 ** 042568 2 SCREW HHC M6-1.0 X 20 G8.8 76 ** 022473 2 WASHER FLAT 1/4-M6 ZINC 77 ** 022097 2 WASHER LOCK M6-1/4 78 ** 049813 2 NUT HEX M6 X 1.0 G8 YEL CHR 79 0D2244M 1 ASSY MAGPICKUP (3/8-24 MALE) * CLAMP FOR WIRING HARNESS (NOT SHOWN) ** NOT SHOWN 1 2 026812 075580 2 1 ELBOW 90D 3/4 NPT FLANGE FUEL INLET 3 0F6364A 1 FUEL RGLTR 1.5L REWORK 4 039253 4 SCREW HHC M8-1.25 X 20 G8.8 5 6 7 022145 022129 045771 2 6 2 WASHER FLAT 5/16 ZINC WASHER LOCK M8-5/16 NUT HEX M8-1.25 G8 YEL CHR 8 * 0F1570 1 BODY CARBURETOR ASSEMBLY 9 10 11 12 032552 029032 025424 0F0397 1 1 1 1 BARBED EL 90 5/16 X 1/8 NPT HOSE 9/32 ID NIPPLE PIPE 3/4 NPT X 6 HOSE CRANKCASE BREATHER 13 0A5547 1 COVER AIR CLEANER 14 15 048031C 0D1509 4 1 CLAMP HOSE BAND 1/4 DECAL INLET PRESSURE 16 * 0E0591 1 ADAPTER CARB. TO AIR CLNR 17 059402 1 FILTER ELEMENT 18 19 037561 0E1028C 1 1 NUT WING 1/4-20 NYLK ASSY CARBURETOR 1.5L C1 CPL 20 059401 1 CARBURETOR GASKET 21 * 091526 4 SCREW PPHM M5-0.8 X 12 ZNC 22 * 049226 4 WASHER LOCK M5 23 24 25 26 27 ** 026915 062522 022127 022259 050279 2 1 1 2 1 NIPPLE CLOSE 3/4 X 1.375 STUD TH 1/4-20 X 3 G2 ZNC FULL NUT HEX 1/4-20 STEEL NUT HEX 5/16-18 STEEL DECAL FUEL INLET NG 050280 1 DECAL FUEL INLET LPG 28 29 0A6125 0F6155 2 1 STUD 5/16-18 X 1.25 F THR HARNESS FUEL JUMPER SINGLE REG 30 * 0E1104 1 GASKET AIR CLEANER ADAPTER 31 * 0E0668 1 O-RING 2-028 1.38 X 1.50 X .06 32 * 0E0590 1 VENTURI 18MM 33 * 0C5133 1 O-RING 29.82 X 2.62 34 * 0E0665 1 SCREW THROTTLE PIN STOP 35 * 0E1108 1 THROTTLE ARM REWORK 36 * 37 * 033138 022152 1 1 SCREW HHM #10-32 X 5/8 WASHER LOCK #10 38 * 0E0645 1 LEVER THROTTLE STOP 39 * 40 41 034339 059194 057823 1 1 2 BARBED EL 90 3/8 NPT X 5/8 HOSE 5/8 ID LPG & NG (24” LG) CLAMP HOSE #10 .56 -1.06 42 040173 2 CLAMP HOSE #5.5 .62-.62 43 * 44 45 089617 030340 0A7040 1 1 1 BARBED STR 1/4 NPT X 1/4 MALE HOSE 1/4 ID SAE 30R7 BRACKET-RAD HOSE * INCLUDED IN ITEM 19 (CARBURETOR ASSY ) NOTES: 1. REGULATOR (I/N 3) AS SHOWN IN ILLUSTRATION IS SET UP FOR NATURAL GAS APPLICATION. 2. TO CONFIGURE REGULATOR FOR LP VAPOR, SWITCH HOSE BARB, HOSE CLAMP (I/N 41) AND HOSE (I/N 40) FROM “OUT-1” TO “OUT-2”. REPLACE PIPE PLUG FROM “OUT-2” TO “OUT-1”. USE PIPE SEALANT ON HOSE BARB AND PIPE PLUG. MAKE SURE TO KEEP PORTS FREE FROM DEBRIS DURING RECONFIGURATION PROCESS. 3.** 4 . FOR LP VAPOR APPLICATION SUBSTITUE LPG FUEL INLET DECAL P/N 050280 FOR NG FUEL INLET DECAL P/N 050279 (ITEM 27). WHEN SWITCHING FUEL TYPES, THE PROPER DIP SWITCH SITTINGS MUST BE MADE TO THE CONTROL PANEL. SEE OWNERS MANUAL, FUEL SECTION FOR MORE DETAILS. 1234567 0F7003 (XX) 0F7004 (XX) 0F7008 (XX) 0F7005 (XX) 0F7007 (XX) 0F7006 (XX) 0C2634A 1 1 1 1 2 1 1 ROOF C1 CPL CORNER POST LH SIDE C1 CPL DOOR REAR C1 CPL CORNER POST RH SIDE C1 CPL DOOR LH & RH SIDE C1 CPL DUCT FRONT DISCHARGE C1 CPL ASSEMBLY COVER ACCESS 8 9 10 11 0912970091 0912970090 0E5968 0E3257 1 2 1 6 ASSY WIRE 14AWG 13.8" GRN/YEL ASSY WIRE 14AWG 33.5" GRN/YEL GASKET EXTRUDED TRIM (356” LG) SCREW HWHTF M6-1.0 X 16 12 ** 077992 18 NUT HEX LOCK M6-1.0 SS NY INS 13 0F5049 3 TAB PULL 14 15 16 17 18 19 0F5048 022473 022097 022127 0C2454 078115 3 1 1 1 24 20 LATCH VISE ACTION 5/16 HEX SKT WASHER FLAT 1/4-M6 ZINC WASHER LOCK M6-1/4 NUT HEX 1/4-20 STEEL SCREW THF M6-1 X 16 N WA Z/JS WASHER SELF LOCKING DOME 20 21 22 0F3890B 0F3890 0F7365 2 4 2 RETAINER INSULATION (820) RETAINER INSULATION (450) INSULATION SIDE DOOR C1 23 0F7365B 1 INSULATION REAR DOOR C1 CPL 24 0F7365A 1 INSULATION ROOF C1 CPL OPTIONAL COMPARTMENT MATERIALS: ALL P/N’S WITH AN (XX) SUFFIX INDICATE A MULTIPLE MATERIAL AND COLOR OPTION. USE THE FOLLOWING LEGEND TO IDENTIFY THE CORRECT PART NUMBER: PART NO. MATERIAL COLOR 0XXXXXSN STEEL TAN 0XXXXXAN ALUMINUM TAN 0XXXXXSG STEEL GRAY 0XXXXXAG ALUMINUM GRAY ** ALUMINUM ENCLOSURE NOTE: ALL ENCLOSURE PANELS THAT FASTEN TO THE BASE FRAME MUST BE SECURED USING ITEM 18 & 11 THREAD FORMING FASTENER AND ITEM 12 LOCK NUT. LOCK NUT IS TO BE INSTALLED AFTER THREAD FORMING FASTENER HAS PENETRATED THROUGH EXTRUSIONS IN ENCLOSURE PANELS. ALL ROOF PANELS ARE TO BE SECURED IN THE SAME MANNER. 0F7366 1 MUFFLER C1 0F7647 1 MUFFLER SADDLE 0F8095 1 PIPE EXHAUST OUTLET 0F7538 1 PIPE EXH INLET MUFLR SIDE 1.5L 0E3257 4 SCREW HWHTF M6-1.0 X 16 0F7644 2 MUFFLER STRAP 0C6119 036434 036449 1 3 3 BOLT U 5/16-18 X 2-1/4 BOLT U 5/16-18 X 2.09 SADDLE 2 INCH 022129 022259 038750 8 6 1 WASHER LOCK M8-5/16 NUT HEX 5/16-18 STEEL SCREW HHC M6-1.0 X 30 G8.8 0F7539 1 PIPE EX INLET MANIFLD SIDE 1.5 0E0170 1 EXHAUST BLANKET 800MM 0E2844 1 NIPPLE TOE 1.5NPTX5.5 BLK IRON 049813 1 NUT HEX M6 X 1.0 G8 YEL CHR 022473 022097 6 1 WASHER FLAT 1/4-M6 ZINC WASHER LOCK M6-1/4 Standby Generator Sets Warranty Standby Generator Sets Warranty GENERAC POWER SYST...