There are no user serviceable parts in this equipment. All installation and service to this equipment should be performed by qualified licensed personnel. Do not exceed 30 minutes in a steambath. Excessive exposure can be harmful to your health. Excessive exposure can produce a rapid pulse, light-headedness, weakness or fainting. If you become uncomfortable or experience any of the above conditions exit the steambath immediately. Steambaths can put stress on the body. Therefore a steambath shoul

10 Insert and close the safety pins. 11 Remove the cap from the receptacle socket and connect the electrical plug. Note: Make sure the safety pins are properly installed before raising the mast. Test the Machine Functions By raising and extending, then retracting and lowering the mast back to the horizontal position, the following functions will be tested: winches, latches, mast extension and mast rotation. 12 Unlock the mast hold-down latch. 13 Turn the raise/lower winch handle clockwise until

If more than one operator is expected to use a machine at different times in the same work shift, each operator is expected to follow all safety rules and instructions in the operator's manual. That means every new operator should perform a pre- operation inspection, function tests and a work place inspection before using the machine. Setup Make sure the machine is set up according to the Setup procedure in the Function Tests section. Starting the Engine 1 Make sure the circuit breaker light swi

This procedure should be scheduled monthly or more often depending on local water conditions and steam bath usage FLUSHING PROCEDURE 1. The generator should be cool 2. Turn control on. 3 Open the drain valve. A The unit will drain without heating the water 5. Allow the water to run 10 minutes 6 Close the drain valve WARNING Electric Shock Hazard-High voltage exists within this equipment There are no user serviceable parts in this equipment, All installation and service to this equipment

If we can be of any assistance do not hesitate to call our Service Department at 1*800-331-0349. FOR THE SAFETY OF YOU AND YOUR FAMILY PLEASE READ THE WARNINGS TO THE RIGHT AND ALL INSTRUCTIONS BEFORE USING YOUR STEAMBATH. POST "STEAMBATH INSTRUCTIONS” LABEL OUTSIDE STEAMBATH FOR SAFETY WARNINGS. SECTION 1: OPERATION OF YOUR NEW AMEREC GENERATOR 1. Assure that both the power circuit and water supply to the generator are ON 2. To activate the steam press the control on. In 10 to 20 minutes t

If we can be of any assistance do not hesitate to call our Service Department at 1*800-331-0349. FOR THE SAFETY OF YOU AND YOUR FAMILY PLEASE READ THE WARNINGS TO THE RIGHT AND ALL INSTRUCTIONS BEFORE USING YOUR STEAMBATH. POST "STEAMBATH INSTRUCTIONS” LABEL OUTSIDE STEAMBATH FOR SAFETY WARNINGS. SECTION 1: OPERATION OF YOUR NEW AMEREC GENERATOR 1. Assure that both the power circuit and water supply to the generator are ON 2. To activate the steam press the control on. In 10 to 20 minutes t

If we can be of any assistance do not hesitate to call our Service Department at 1*800-331-0349. FOR THE SAFETY OF YOU AND YOUR FAMILY PLEASE READ THE WARNINGS TO THE RIGHT AND ALL INSTRUCTIONS BEFORE USING YOUR STEAMBATH. POST "STEAMBATH INSTRUCTIONS” LABEL OUTSIDE STEAMBATH FOR SAFETY WARNINGS. SECTION 1: OPERATION OF YOUR NEW AMEREC GENERATOR 1. Assure that both the power circuit and water supply to the generator are ON 2. To activate the steam press the control on. In 10 to 20 minutes t

Use the on/off button to control the temperature as desired SECTION 2: MAINTENANCE OF THE AK SERIES The steam generator, steam head, fittings and piumb-ing connections should be inspected annually lor water leaks and damage The AK steam generator is equipped with a drain vaive forflushing sediments from the generatortank. This procedure should be scheduled monthly or more often depending on local water conditions and steam bath usage FLUSHING PROCEDURE 1. The generator should be cool 2. Tu

If we can be of any assistance do not hesitate to call our Service Department at 1*800-331-0349. FOR THE SAFETY OF YOU AND YOUR FAMILY PLEASE READ THE WARNINGS TO THE RIGHT AND ALL INSTRUCTIONS BEFORE USING YOUR STEAMBATH. POST "STEAMBATH INSTRUCTIONS” LABEL OUTSIDE STEAMBATH FOR SAFETY WARNINGS. SECTION 1: OPERATION OF YOUR NEW AMEREC GENERATOR 1. Assure that both the power circuit and water supply to the generator are ON 2. To activate the steam press the control on. In 10 to 20 minutes t

This procedure should be scheduled monthly or more often depending on local water conditions and steam bath usage FLUSHING PROCEDURE 1. The generator should be cool 2. Turn control on. 3 Open the drain valve. A The unit will drain without heating the water 5. Allow the water to run 10 minutes 6 Close the drain valve WARNING Electric Shock Hazard-High voltage exists within this equipment There are no user serviceable parts in this equipment, All installation and service to this equipment