Assessments - 4, GPA: 3.8
(
)
)
|
Facilidade de uso
CONSULT LOCAL AUTHORITIES IF IN DOUBT ABOUT YOUR LOCAL FIRE SAFETY REGULATIONS. ALL INSTALLATIONS MUST BE MADE IN ACCORDANCE WITH LOCAL AND STATE OR PROVINCIAL CODES WHICH MAY DIFFER FROM THIS MANUAL. IMPROPER INSTALLATION WILL RESULT IN VOIDING OF WARRANTY. SCOTTY WOOD FURNACE – INSTRUCTION MANUAL Scotty 2 Oct-06 TABLE OF CONTENTS Specifications 3 1.0 Operating Instructions 4 1.1 Introduction 4 1.2 Wood-Burning 4 1.3 Storage of Wood 5 1.4 Maximum Solid-Fuel Charge 6 1.5 Maintenance 6 1.5.1 Cleaning 6 1.5.2 Servicing 7 1.6 Safety 7 1.7 Controls 7 1.8 Electrical Power Failure 8 1.9 Homeowner Checklist 9 2.0 Installation Instructions 9 2.1 Introduction to Installers 9 2.2 Uncrating 10 2.3 Locating the Furnace 10 2.4.1 Combustion Air Supply 11 2.4.2 Flue Pipe & Chimney 11 2.5 Clearances 12 2.6 Duct Connection 13 2.7 Free Standing 14 2.8 Control System 14 2.9 Installers Checklist 15 DIAGRAMS S102 – 1 Clearances S102 – 2 Combustible Floor Base S102 – 3 Control Placement Detail S102 – 4 Free Standing Wiring Diagram S102 – 5 Control Placement S102 – 6 Cleaning S102 – 7 Ductwork Configurations Appendices APPENDIX A – Warranty Rear Cover SCOTTY WOOD FURNACE – INSTRUCTION MANUAL Scotty 3 Oct-06 KERR SCOTTY Wood Furnace Model DB-102 Certified by the Canadian Standards Association Manufactured by: Parrsboro Metal Fabricators Ltd. P.O. Box 637, Crossroads 12118, Highway 209 Parrsboro, Nova Scotia, Canada B0M 1S0 SPECIFICATIONS Length 46 1/2” Width 22 1/2” Height 43” Shipping Weight 344 lb Fire Box 1/8”plate Length 27 1/2” Diameter 18” Secondary Heat Exchanger 14 gauge steel Fire Box Door Cast Iron 12” x 12” Warm Air Plenum 29” x 20 3/4” Return Air Plenum 14 .” x 20 3/4” Air Filter Size 16” x 20” x 1” Blower Size G9 – 10 Blower Motor 1/4 hp CFM 1000 (Required) Smoke Pipe 7” Inside Diameter Floor to smoke pipe center 36” Output (max) 70,000 Btu/h Fuel Wood 24” logs Electrical Rating Volts 120, Cycles 60, Amps 15 NOTE – Keep this manual in a safe place for future reference. Follow manual carefully for the correct way to install and operate this unit. CAUTION – Do not fire this unit until operating instructions have been read and fully understood. INSTALL WOOD FURNACE ONLY ON A FURNACE DUCT SYSTEM AND CHIMNEY THAT ARE IN GOOD CONDITION AND APPROVED FOR USE. SAVE THESE INSTRUCTIONS SCOTTY WOOD FURNACE – INSTRUCTION MANUAL Scotty 4 Oct-06 1.0 OPERATING INSTRUCTIONS 1.1 INTRODUCTION Congratulations on your purchase of the KERR SCOTTY Wood Furnace. Developed in Atlantic Canada, this KERR Furnace has been designed to allow you to heat your home with wood, one of North America’s most abundant fuels. Designed with you in mind, the KERR SCOTTY Wood Furnace will provide you with many years of safe, efficient central heating. To ensure you have a clear understanding of the operating procedures of this furnace, please take the time to read the remainder of this section on operating procedures. If you have any questions, your KERR DEALER will be happy to answer them for you. 1.2 WOOD-BURNING The SCOTTY Wood Furnace will burn most wood fuels, however it is recommended that only dry, seasoned hardwood be used as much as possible since it affords cleaner, safer and more efficient operation. Burning seasoned hardwood will leave less ash, soot and creosote residue and will require fueling less often. Use smaller loads of wood on warmer days. WARNING: DO NOT use chemicals or fluids to start the fire or during operation. DO NOT burn driftwood or manufactured logs (compressed wood). Before adding fuel to an existing fire turn up the thermostat for about five minutes or lift damper chain to hold damper fully open for about one minute before opening the loading door. This action will allow residual smoke to clear from the combustion chamber and reduce smoke entering the basement during refueling. Twice daily refueling may be sufficient in modern well-insulated homes. However, KERR recommends that small fuel loads be added morning, noon and early evening and late evening, rather than large quantities infrequently. A small intense fire will burn more efficiently than a large smoldering fire in the SCOTTY Wood Furnace and will produce less creosote. When refueling the SCOTTY, the remaining coals should be raked to the front of the combustion chamber before adding any new fuel. Place the fresh supply of wood to the rear of the combustion chamber. This gives more of an even cigar type fuel burn, rather than a large hot fire to a slow amber fire. This will help create a more even and efficient burn. The SCOTTY owner should attempt to gauge fuel quantities with outdoor temperatures; a little practice will provide greater satisfaction and efficiency. WARNING: This furnace is not to be used with an automatic stoker. Keep firing door tightly closed and maintain door seal in good condition. SCOTTY WOOD FURNACE – INSTRUCTION MANUAL Scotty 5 Oct-06 CREOSOTE Wood combustion is never 100% complete. Wood smoke always contains some unburned gases and a mixture o...