Assessments - 4, GPA: 4.5
(
)
)
|
Facilidade de uso
Snap pedestal into the bottom of the heater housing. Refer to Figure 1, 2. Base Assembly Step 1: If the base is in two halves, snap them together by sliding slots of one base half into slots of second base half. Refer to Figure 3. Step 2: Run the power cord through the center of the assembled base. To assemble the base to the unit (either one or two-piece base) first make sure the side marked “Rear” is facing the back of the heater. Line up holes of the base with holes on bottom of pedestal (or heater housing if no pedestal is included), and secure with 4 provided screws. Refer to Figure 4. Step 3: Lace the power cord through the cord minders on the underside of the base. Refer to Figure 5. Step 4: Turn the heater right side up on a flat level surface prior to beginning operation. When using electrical appliances, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons, including the following: 1. Read all instructions before using the appliance. 2. To avoid fire or shock hazard, plug the appliance directly into a 120V AC electrical outlet. 3. The heater is hot when in use. To avoid burns, DO NOT let bare skin touch hot surfaces. If provided, use handles when moving this heater. Keep combustible materials, such as furniture, pillows, bedding, papers, clothes, and curtains at least 3 ft (0.9 m) from the front of the heater and keep them away from the sides and rear. 4. DO NOT run cord under carpeting. DO NOT cover cord with throw rugs, runners, or the like. Arrange cord away from traffic area and where it will not be tripped over. 5. This heater is not intended for use in bathrooms, laundry areas and similar indoor location. NEVER locate heater where it may fall into a bathtub or other water container. 6. Extreme caution is necessary when any heater is used by, or near children or invalids, and whenever the heater is left operating and unattended. 7. Always unplug the heater when not in use. 8. When unplugging, be sure to pull by the plug and not the cord. 9. DO NOT insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric shock or fire, or damage the heater. 10. DO NOT operate heater with a damaged cord or plug, or after the heater malfunctions, has been dropped or damaged in any manner. Return appliance to manufacturer for examination, electrical or mechanical adjustment, or repair. 11. A heater has hot and arcing or sparking parts inside. DO NOT use it in areas where gasoline, paint, or flammable liquids are used or stored. 12. Use appliance only for intended household use as described in this manual. Any other use not recommended by the manufacturer may cause fire, electric shock, or injury to persons. The use of attachments not recommended or sold by the manufacturer may cause hazards. 13. DO NOT use outdoors. 14. To prevent a possible fire, DO NOT block air intakes or exhaust in any manner. DO NOT use on soft surfaces, like a bed, where openings may become blocked. 15. To disconnect heater, turn controls to OFF, then remove plug from outlet. 16. Avoid the use of an extension cord because the extension cord may overheat and cause a risk of fire. However, if you have to use an extension cord, the cord shall be No. 14 AWG minimum size and rated not less than 1875 watts. 17. If the heater will not operate, see specific instructions on Auto Safety Shut-off. 18. DO NOT attempt to repair or adjust any electrical or mechanical functions on this unit. Doing so will void your warranty. The inside of the unit contains no user serviceable parts. All servicing should be performed by qualified personnel only. 19. Discontinue use if plug or outlet is hot. It is recommended that the outlet be replaced if plug or outlet is hot to touch. PLEASE READ AND SAVE THESE IMPORTANT SAFETY INSTRUCTIONS F E AT U R E S - O P E R ATIONS V E U I L L E Z L I R E E T C O N S E RV E R C E S D I R E C T I V E S D E S E C U R I T E I M P O RTANTES INSTRUCTIONS D’ASSEMBLAGE C A R A C T E R I S T I Q U E S – U T I L I S ATION THIS APPLIANCE HAS A POLARIZED PLUG (one blade is wider than the other). To reduce the risk of electric shock, this plug is intended to fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. DO NOT ATTEMPT TO MODIFY THIS PLUG OR DEFEAT THIS SAFETY FEATURE IN ANY WAY. CET APPAREIL EST DOTE D'UN CORDON A FICHE POLARISEE (une lame est plus large que l'autre). Afin de reduire les risques d'electrocution, cette fiche n’enfonce que dans un sens dans la prise electrique. Si la fiche ne s'insere pas dans la prise, retournez la fiche. Si elle ne s'adapte toujours pas, contactez un electricien qualifie afin d'installer la prise appropriee. NE CONTOURNEZ PAS CE DISPOSITIF DE SECURITE ET N'ALTEREZ LA FICHE EN AUCUNE FACON. Fan Only Setting Press the Fan Only Button to run the heater witho...