Assessments - 3, GPA: 4
(
)
)
|
Facilidade de uso
Electrical connection WARNING – THIS APPLIANCE MUST BE EARTHED This heater must be used on an ~ supply only and the voltage marked on the heater must correspond to the supply voltage. This heater is fitted with a rewireable plug incorporating a 13 amp fuse. In the event of replacing the fuse in the plug supplied, a 13 amp fuse approved by ASTA to BS 1362 must be used. If any other type of plug is used, a 15 amp fuse must be fitted in the plug, the adaptor, or at the distribution board. IMPORTANT : If the plug is not suitable for your socket, the 13 amp plug should be removed. Before wiring the appropriate plug, please note that the wires in this mains lead are coloured in accordance with the following code : GREEN AND YELLOW: EARTH BLUE : NEUTRAL BROWN : LIVE Connect the GREEN AND YELLOW wire to the terminal marked ‘E’ or by the earth symbol , or coloured GREEN or GREEN AND YELLOW. Connect the BROWN wire to the terminal marked ‘L’ or coloured RED. Connect the BLUE wire to the terminal marked ‘N’ or coloured BLACK. Positioning the heater Always ensure that the heater is stood on a firm, level base near to, but not directly beneath, a suitable mains supply socket, ensuring at least 300mm clearance from any shelf above. Ensure that curtains and furniture are not positioned close to the chosen position, as this would create a potential fire hazard. See also ‘Important Safety Advice’. Fitting Feet NEVER USE THE HEATER FREE STANDING WITHOUT THE FEET FITTED. Lay the heater on its back, and locate the foot fixing screw (see ‘a’ in Fig. 2). Remove the screw using an X–head screwdriver, then align foot over slots and holes in base and slide home. Finally take the foot fixing screw, insert and tighten using a screwdriver to secure the foot. Fig. 2 Fig. 1 Using the heater Plug in and switch on at the wall socket. On standard models with a neon, the red POWER ON neon will light when the heater is connected to the power supply. On timer models the timer clock will operate all the time that the heater is connected to the mains supply. On model DXLAT150 the heat selector switch positions are as follows: O -Off I -Low Heat (750W) II -High Heat (1500W) On model DXLAT75 there is an On /Off switch – operation as follows: O -Off I -On (750W) Model DXLAT150Ti is controlled by a Digital Timer – see ‘Digital Timer Operation’ The heat output is controlled by the thermostat - see ‘Thermostat’ Please note – the element has been coated with a protective film which will burn off during the first few minutes of use and may cause a small amount of fuming. This is quite normal – the fumes are non-toxic and will quickly disappear. We recommend that you open a window to ventilate the room when using the heater for the first time. Controls Thermostat -see Fig. 3 The thermostat controls the heat output according to the room temperature. Fig. 3 This ensures that the heater will not produce heat unnecessarily when the room is warm. To set the temperature you require, turn the thermostat knob clockwise until the desired temperature is reached. Alternatively to heat a cold room quickly, turn the thermostat knob up fully. When the room has reached the desired temperature, turn the thermostat knob anti-clockwise until the thermostat just clicks off. The heater will now automatically operate at this temperature. The thermostat also has a frost protection setting marked ‘*’. This setting is useful in areas such as garages to prevent frost damage. If the thermostat is set to its minimum setting ‘*’, the heater will cycle ON and OFF to maintain a temperature of approximately 5°C to help protect against frosty conditions. Digital Timer Operation - see Fig. 4 IMPORTANT: Remember to observe all safety warnings when operating the heater on auto setting, either attended or unattended. The timer allows you to select ‘AUTO’ or ‘MAN ON’ by pressing the ‘MODE’ button until the required MODE appears at the bottom of the timer display. ‘AUTO’ MODE allows the heater to switch ON and OFF according to a set 24 Hour program period (see ‘Setting Programs’ section below). ‘MAN ON’ MODE allows power to the heater uninterrupted by the program settings. Key ...
Este manual também é adequado para os modelos :Eléctrico - DXLAT150Ti (767.94 kb)
Eléctrico - DXLAT75 (767.94 kb)