Assessments - 2, GPA: 4.5
(
)
)
|
Facilidade de uso
Height 1 1 2 g c d b a (3) (8) (4) f e (5) 500 MIN. 882 306 882 146 297 297 500 MIN. Dimplex CXD Ceramic Radiant Heater Model(s) : CXD2000H-NA THESE INSTRUCTIONS SHOULD BE READ CAREFULLYAND RETAINED FOR FUTURE REFERENCE Important Safety Advice Because the Dimplex Ceramic Radiant Heater contains no moving parts little maintenance is required. Before undertaking any maintenance work on the heater due attention must be paid to the following: This heater is designed to be horizontally wall mounted only, it must not be ceiling mounted. Always ensure a safe mounting height, at or above a minimum height of 1.8 metres from ground level, so that the heater can not be touched when in operation. The heater must be wall mounted level ± 5. to the horizontal. Do not locate the heater immediately above or below a fixed socket outlet or connection box. Always disconnect the heater from the electricity supply before attempting to work on or near it. Always ensure a safe means of access using an access tower or properly supported ladder. Do not cover the heater. Keep combustible materials away from the heater. Do not position patio furniture, sunshades, awnings and other combustible materials too close to the heater. Do not use heater if the elements are broken - as injury may occur. Allow adequate time (minimum of 30 mins.) for the elements and body casing to cool before attempting to work on the heater . Wiring between the heater and the spur outlet or isolation switch must be in a heat resisting cable (e.g. polychloroprene). Do not install less than 1.8 metres (6 feet) from ground level. Warning: Please ensure all packaging is removed from the appliance before switching on. General Your Dimplex Ceramic Radiant Heater uses ceramic elements which produce a high proportion of their output in the long-wave infra-red. This provides a high comfort factor – similar to the natural energy from the sun. Electrical The installation of this appliance should be carried out by a competent electrician and be in accordance with the current IEE wiring regulations and any local or insurance regulations. The CXD2000H-NA is designed for use on a 230-240V AC single phase supply. An all-pole isolating switch with a minimum separation of 3mm in each pole must be fitted to facilitate isolation. This switch must either be positioned inside a building or have an IP rating against water ingress suitable for external installation. The appliance must be supplied through a residual current device (RCD) having a rated residual operating current not exceeding 30mA. The appliance must be connected to a socket-outlet having an earthing contact. We recommend that a cable with a minimum specification of H07RNF polychloroprene sheathed or similar be used with a minimum temperature rating of 90°C. The wiring to the appliance must be connected with a UL approved watertight connection for outdoor use. Remove rain shield for access to this connection and then replace rain shield once connection is completed. Appliance must have rain shield installed at all times during operation. Note : Always ensure the cable grip is tightened. Installation Heaters are supplied with an integral wall bracket which may be fixed through the mounting holes to any suitable structure. The bracket positions the heater at the an angle of 45 degrees for optimum performance. The recommended fixing height is 1.8m from ground level - see Fig. 2. The integral wall fixing bracket may be removed by fully unscrewing to facilitate its fixing. The siting of the heater(s) should be such as to allow an even and uninterrupted distribution of radiation to the area(s) to be heated. When deciding upon the best location, consideration must be given to the following requirements: a. Avoid structures which might vibrate e.g. crane gantries. These could adversely affect element life. b. Comfort and safety could be compromised unless the heater is mounted at or above 1.8m from ground level. c. Allow a minimum of 500mm minimum clearance between the top of the heater and any horizontal surface - see Fig. 1. Element Replacement (see Fig. 4) WARNING – BEFORE UNDERTAKING THIS TASK ENSURE THE HEATER IS DISCONNECTED FROM THE ELECRICITY SUPPLYAND LEFT TO COOL FOR A MINIMUM OF 30 MINUTES. 1. The heater should be taken off the wall. 2. Remove 3 screws to remove the rain shield (see ‘a’ in Fig. 4) to gain access to the control box on the back of the heater. 3. Remove 4 screws to remove the terminal block plate (see ‘b’ in Fig. 4) and disconnect the terminal block. 4. Remove 8 screws to remove the control box (see ‘c’ in Fig. 4). 5. This will allow access to the elements. Remove the retaining clips and spring clips (f) to loosen the elements. 6. Disconnect the elements from their terminal blocks. 7. Remove the remaining 5 screws which hold the back panel (see ‘d’ in Fig. 4). 8. Remove the splash brackets (see ‘g’ in Fig. 4) on the elements. 9. Bend the bars on the guard as indicated in Fig. 3 to remove it. 10. The old...