Assessments - 1, GPA: 4
(
)
)
|
Facilidade de uso
Carefully read all of the instructions below before using this heater. 1. This heater is hot when in use. To avoid burns, do not let bare skin touch the heater’s hot surfaces. Use the provided handles when moving this heater. Keep combustible materials such as furniture, pillows, bedding, paper, clothes, and curtains at least 3 feet (0.9m) from the front of the heater. Also keep these materials away from the sides and rear of the heater. 2. Extreme caution is necessary when this heater is used by or near children or invalids and whenever the heater is left operating unattended. 3. Always unplug the heater when not in use. 4. Do not operate this heater if it has a damaged cord or plug, or after the heater malfunctions, has been dropped, or damaged in any manner. Return the heater to an authorized service facility for any repairs or for electrical or mechanical adjustments. 5. Do not use this heater outdoors. 6. This heater is not intended for use in wet or damp locations such as bathrooms or laundry areas. Never place this heater anywhere where it may fall into or near water. 7. Do not run the power cord under carpeting. Do not cover the power cord with throw rugs, runners, or similar coverings. Arrange the power cord away from traffic areas where it will not be tripped over. 8. To disconnect the heater, first turn the controls off, and then remove the plug from the outlet. 9. Do not insert or allow foreign objects to enter any ventilation or exhaust openings as this may cause electric shock, fire, or damage to the heater. 10. To prevent a possible fire, do not block the unit’s air intakes or exhaust. Do not use the heater on soft surfaces (such as beds) where openings may become blocked. 11. This heater may have hot, arcing, or sparking parts inside. Do not use this heater in or near areas where gasoline, paint, or other flammable liquids are used or stored. 12. Only use this heater as described in this manual. Any other use not recommended by the manufacturer may cause fire, electric shock, or injury. 13. When possible, avoid the use of extension cords because the cord may overheat and cause a risk of fire. If extension cords must be used, minimize the risk of overheating by making sure they are UL listed, a minimum No. 14 AWG, and rated no less than 1875 watts. 14. This heater draws 12.5 amps during operation. To prevent overloading a circuit, do not plug the heater into a circuit that already has other appliances running. 15. It is normal for the plug to feel warm to the touch; however, a loose fit between the AC outlet (receptacle) and plug may cause overheating and distortion of the plug. Contact a qualified electrician to replace loose or worn outlets. 16. The output of this heater may vary, and its temperature may become intense enough to burn exposed skin. Use of this heater is not recommended for persons with reduced sensitivity to heat. .. Place the heater on a firm, level surface free from obstructions and at least 3 feet away from walls or other objects such as furniture, curtains, plants, or combustible materials. .. To program your electric oil-filled heater, refer to the control panel diagram in Fig. 2 below: .. Press the “POWER” button to turn the heater ON. .. Select the heat level you desire by pressing the POWER button. The heater will turn on in the following sequence: HI-MED-LO. On LO, the heater will operate at 600W. On MED, the heater will operate at 900W. On HI, the heater will operate at 1500W. .. There are 5 temperature settings, ranging from MIN to MAX. Press the “TEMP” button to select the desired temperature. The heater will operate in the following sequence: 65 oF, 70 oF, 75 oF , 80 oF, and 85 oF. .. Press the “TIMER” button to set the desired heating time. There are three choices: 2H (2 hours), 4H (4 hours), and 8H (8 hours). .. Timer setting: This heater has an 8 hour On/Off timer. You can set the “On” timer when the heater is in “stand-by” mode (unit is plugged in but not operating), or you can set the “Off” timer when the heater is operating. For example, you can plug in the heater and set the timer to turn the unit on after 2 hours, or you can also set the timer to turn the heater off after 4 hours when the heater is in operation. UNPACKING AND SET-UP INSTRUCTIONS Carefully unpack your heater and remove the wheel assemblies from the packaging. Refer to Fig. 1 below: 1. Make sure the heater is unplugged and turned off. 2. TURN THE HEATER UPSIDE DOWN. 3. Position the wheel base assemblies between the end fins as shown. 4. Insert each U-shape screw into the holes of each wheel holding plate. 5. Insert the butterfly nuts and screw them in tightly. 6. Turn the heater upright. 7. Your heater is now ready for use. CAUTION: To prevent a possible fire, do not operate the heater without the wheel assemblies attached. Only operate the heater in an upright position with the wheels on the bottom and controls on top. Operating the unit in any other position could result in fire, persona...