Assessments - 1, GPA: 4
(
)
)
|
Facilidade de uso
PLEASE DO NOT ATTEMPT TO OPEN OR REPAIR THE HEATER YOURSELF. DOING SO MAY VOID THE WARRANTY AND COULD CAUSE DAMAGE OR PERSONAL INJURY. CLEANING AND STORAGE It is recommended that the heater be cleaned at least one time during the operating season in order to provide the optimum level of performance. ALWAYS TURN THE POWER SWITCH OFF AND UNPLUG THE HEATER BEFORE CLEANING. Be sure to save the box for offseason storage. . Turn the heater “ OFF” , unplug it and wait for the heater to cool down. . Use a dry cloth to clean only external surfaces of the heater. . Do not use any cleaning agents or detergents. . Never immerse the heater in water. . Pack the heater in the original carton and store it in a cool and dry place. SPECIFICATIONS Model No.: HC-0119A Voltage: 120V, 60Hz Current: Maximum continuous draw: 12.5 Amps. Power: LO = 900 Watts, HI = 1500 Watts. Tolerances on all specifications: Approximately +5%, -10%. B. If the setting temperature is lower than or equal to the room temperature, the temperature display will flash and the unit will stop heating. When the room temperature falls down to less than the setting temperature, the unit will resume heating. The heater will cycle on and off this way to maintain the setting temperature. Note: Every time you turn on the heater, the heater will heat forcedly for 2 minutes. After that the heater will work based on the below instruction. And when the room temperature reaches the setting temperature or the setting temperature is lower or equal to the room temperature, the heating element will shut off immediately, but the fan motor will continue running for 10—30 seconds before shutting off. This is a safety feature to protect the unit from being too hot. . Timer setting: This heater has an 8 hours On/Off timer. You can set an “ On” timer when the heater is standing by (plugged in but not working) or you can set an “ Off” timer when the heater is working. For example, you can plug in the heater and set the timer to turn the heater on after 3 hours, you can also set the timer to turn the heater off after 6 hours and a half when the heater is working. Example for “ On” Timer: 1. When the heater is plugged in and not working, press the “ C” Timer and the “ A” Digital Indicator will display the last set value (0.0 is the default set). Press the “ Up” or “ Down” key to choose your desired timer setting. The timer will increase or decrease half on hour every time you press the “ Up” or “ Down” key and goes up and down from 0.0 to 8.0. 2. Press “ Up” key 6 times until 3.0 is displayed, press the “ C” Timer again to confirm the set. Now your heater is set to be turned on after 3 hours. Example for “ Off” Timer: 1. When the heater is working, press the “ C” Timer. 2. Press “ Up” key 13 times or “ Down” key 3 times until 6.5 is displayed, press the “ C” Timer again to confirm the set. Now your heater is set to be turned off after 6 hours and a half. To disable the timer, adjust the set value of the timer to 0.0. Note: Once the timer is set, the heater will work this way unless you unplug the heater. You have to reset the timer every time you plug in your heater. . Remote control (Refer to Fig 2): This heater has a 6 key remote with the following function (See picture above): 1. ON/OFF: Power switch key, used to turn off the heater when the heater is on. 2. OSC: Oscillation switch, used to enable the oscillation function by pressing once. To disable the oscillation function, press the “OSC” key once more. This key is only valid when the heater is on (Hi, Low or Fan). 3. TIMER: Timer setting key, used to enable the timer setting or confirm the setting value. 4. MODE: Mode select key, used to switch the heater circularly in sequence of HI -LO - FAN when the heater is on. 5. “ +” and “ -” : Value adjustment key, used to adjust the set value of the temperature or the timer. CAUTION: This heater includes an Overheat Protection System that shuts the unit off if it overheats due to abnormal conditions. If this occurs turn the heater “OFF”, unplug it, and inspect and remove any objects on or adjacent to the heater. Allow it to cool for a few minutes, plug it back in, and resume normal operation. SERVICE & SUPPORT In the event of a warranty claim or if service is required for this heater, please contact us at the following: Toll Free: 866-876-4332 (M-F 8:30am to 5:30pm CST) Email us at: Service@Pelonis.com For questions or comments, please write to: Pelonis USA, Ltd. 2617 North Great Southwest Parkway Suite 100 Grand Prairie, TX 75050, USA For your records, staple your sales receipt to this manual and record the following: DATE OF PURCHASE: ________________________________________________________________ PLACE OF PURCHASE: ________________________________________________________________ SERIAL NUMBER: ________________________________________________________________ (STAPLE SALES RECEIPT HERE) NOTE: PROOF OF PURCHASE IS REQUIRED FOR ALL WARRANTY CLAIMS ONE (1) YEAR LIMITED WARRANTY . Ple...