Assessments - 2, GPA: 4.5
(
)
)
|
Facilidade de uso
Фрунзе, 45 (8634) 46-47-54 33. Ижевск Радиокомплект ул. 9-я Подлесская, 25 (3412)59-28-05 34. Барнаул Vitek - сервис ул. Попова, 68 (3852) 35-37-50 35-37-51 35. Новосибирск ООО "Техмастер" ул. Большевитская, 131 (3832) 12-54-00 36. Омск Космос Космический пр-т, 97А, к.4 (3919)53-98-41 Получить информацию о других сервисных центрах Вы можете у продавца или по адресу в Интернет: ю ENGLISH TO ASSEMBLE 1. Install multidirectional rolling wheels to each end between the first and the second groups of the radiating flanges. 2. Let the "U" shape screw surrounding the dome of the radiating flanges. Then insert it into two holes of the supporting plate. 3. Insert the butterfly nuts and screw them tightly counter clockwise. 4. Combine the tube and plastic rack together as figure. 5. Insert the towel rack assembly to radiator fins along the slot as figure. 11 ll ll X X X X X X X TO USE 1. Insert the plug into the suitable wall outlet. 1) Never use the unit in place where is not plain, make sure there is nothing flammable or easy deform object within 1 m. 2) Insert the plug after setting the thermostat to the "OFF" position and setting the power selected switches to the " OFF" position. 3) The unit should be earthed. Do not cover the appliance. 4) The heater is suitable for operation on an AC electricity supply having the same voltage as that show on it's rating label. 2. Press the power selected switch to the "HIGH" position then turn thermostat to the "HIGH" position, at this moment, the unit begins working, when the temperature rises to what you are satisfied with, slowly turn thermostat counter clockwise until the indicating light of the key for power choice is out, and the room temperature thus can be kept constant. If you want to raise or lower the room temperature, you can make another regulation: Turn the thermostat clockwise to raise the temperature, or count- 3 er-clockwise to lower it and you can also turn the power switch to "LOW" or "MID" position for different power selecting. NOTES: 1 ) The pilot lamp will on only if the temperature is below the setting value of the thermostat. 2) The room must be sealed in good condition, if not, it will not make good result because of the influx of heat. 3) The outlets of the control chamber must be kept ventilative, if not, undue move of the thermostat may occur. 3. After use, switch off the keys for power setting first, then turn the thermostat to the "OFF" position, and pull out the power supply plug. 4. Cleaning and maintenance. 1 ) The electric heater should be cleaned regularly to wipe out the dust in the surface of flanges. As this may result the radiating efficient. 2) Disconnect electricity supply and allow radiator to cool, wipe over with a soft damp cloth. Do not use detergent or abrasives. 3) Do not scrap the surfaces of flanges with sharp hard tools, to avoid surfaces getting rusty, because of damage of the paint coat. CAUTIONS FOR OPERATION 1. Never use the unit in places where are not plain and unstable. 2. Do not insert and pull out the plug with wet hand, as this may cause electrical shock, power supply capacity should be enough. 3. The heater must only be used in the upright position. Never use when the unit is fallen over. 4. The unit should be far away with the object flammable or easy deform during uses. 5. Do not allow smashing the surface with rod or sharp hard tools, as this may cause deform and get rusty because of damage of paint coat. 6. During use surface temperature of the flanges is perhaps higher, thus do not touch it except handle, knob and the keys. 7. Don't heat wet clothing etc. in the surface of the control chamber, as this may cause undue move of the thermostat. IMPORTANT SAFEGUARDS When using any electrical appliance, basic safety precautions should always be followed, including the following. 1. To ensure familiarity with the controls, safety features, and operation of your heater-Read all instructions before use. 2. To reduce hazard of injury due to elect...