Assessments - 2, GPA: 4.5 ( )

Fabricante : Omega Vehicle Security Arquivo Tamanho: 320.66 kb Arquivo Nome : Língua de Ensino:

Use a medium to hard roller to Do not wrap the heater over heater. © Copyright 2006 ENGINEERING, All rights reserved. This document may reproduced, translated, prior written ENGINEERING, MOUNTING YOUR HEATING BLANKET Installation of heater using factory supplied Pressure Sensitive Adhesive (PSA): 3. Peel off the release film [Figure A] and then press the heater onto the surface of the item being heated using a medium to hard rubber roller [Figure B]. Ensure blanket is making intimate contact with the surface to be heated. - The pressure sensitive adhesive will cure when the blanket is energized and heat is generated. PSA generally cures in twenty minutes at 200.F (93.C) in a 68.F (20.C) ambient environment. The cure time will vary with temperature of the blanket and surrounding ambient conditions. The higher the ambient temperature and set-point of the blanket, the faster the cure time. - The blanket may require a temporary method of attachment to secure the heater until the PSA cures. Use a high-temperature adhesive tape to secure the heater. - For larger heaters, press the heater onto the surface as the fi lm is removed. NOTE: OMEGA ® does not recommend allowing pressure sensitive adhesive to cure at temperatures below 40.F (4.C). Figure A: Removing Film Figure B: Rolling the Blanket CONNECTING YOUR HEATING BLANKET TO A POWER SOURCE 1. If your heating blanket does not have its own internal device, it must be connected to an external control device. The heater must not be operated without some form of temperature - Your heater is designed to operate at a specific voltage ±10%. Refer to the label on the heater for proper operating voltage and wattage Failure to operate the heater at the specified rating could result in overheating of the Also note lower-than-rated voltage will - All electrical connections must personnel and in accordance codes and regulations. - SEBHB series: A NRTL (National Recognized Testing Laboratory) listed a failure annunciation The controller must be approved © Copyright 2006 ENGINEERING, All rights reserved. This document may reproduced, translated, prior written ENGINEERING, CONNECTING YOUR HEATING BLANKET TO A POWER SOURCE 2. Most heating blankets are available with an optional high-limit safety thermostat to protect both the heater and the product being heated from damage if the main controlling device fails. This option is especially recommended for surfaces that are high risk for heat damage (e.g. plastic). 3. Ensure heater is protected by a properly rated circuit breaker or fuse. 4. Use of a ground fault circuit interrupter (GFCI) is highly recommended and may be required according to local electric code. 5. Two wires (same color) should be connected to the power source (or temperature control device) directly, through a junction box, or to a connector that is mated to a receptacle connected to the power source. These heating blankets are non-polarized, allowing either wire to be connected to the neutral or hot. The third wire (if applicable), designated by the color green (or a green stripe), should be connected to ground. 6. SEBHB series: The conduit connection is 3/4” hub. TROUBLESHOOTING GUIDE Please read this guide prior to contacting OMEGA. This guide is designed to answer the most commonly asked questions. If you are unable to identify the problem or need additional assistance, please contact us at 1-800-USA- PROBLEM SOLUTION(S) Does not heat Verify heater is connected to proper voltage. Check to see if there is a resistance reading (not an open circuit) in heater using an ohm meter. Pressure sensitive adhesive is not adhering Verify date of manufacture. PSA has a shelf life of six months. Ensure there are no air gaps and heater is making intimate contact with surface being heated. Use medium to hard rubber roller. Circuit breaker is tripping Validate that the circuit breaker is capable the amp requirement of heater. The identification label located on the power cord displays amperage requirement. Examine heater and cord Check to see if there power leads and © Copyright 2006 ENGINEERING, All rights reserved. This document may reproduced, translated, prior written ENGINEERING, M-4281/06 PN: 11661-01 Rev ...

Baixe o seu

Para fazer o download, introduza 2 dígitos :