Assessments - 3, GPA: 3.3
(
)
)
|
Facilidade de uso
Use extreme caution on wooden decks. Keep all electrical cords away from a hot heater. After a period of storage and/or nonuse, inspect for any abrasion, wear, cuts to the electrical cord. The use of accessory attachments not recommended by the appliance manufacturer may cause injuries. Store products indoors when not in use – out of the reach of children. Servicing should be done only while the heater is disconnected from the power supply. To ensure continued protection against electrical shock, connect only to properly grounded outlets. Do not immerse in water. Disconnect electric cord from outlet before cleaning, servicing and/or removing heating element. To reduce the risk of electric shock, use with GFI protected electric outlet only. High temperatures may be generated under certain abnormal conditions. Do not partially or fully cover or obstruct this heater. Please use protective gloves when assembling this product. Do not force parts together as this can result in personal injury or damage to the product. Use this heater only as descibed in this manual. Any other use not recommended by the manufacturer may cause fire, electrical shock, or injury to persons. To reduce risk of shock, keep cord connection dry. Product must be fully assembled before operating the heater. Do not clean this product with a water spray or the like. Deaths, serious injury or damage to property may occur if the above is not followed exactly. page no. Contact 1.800.762.1142 for assistance. Do not return to place of purchase. Parts List Exploded View Finial* 2 Dome* 3 Dome Brace* 4 Plastic Insulator* 5 Upper Pole* 6 Heat Reflector* 7 Bulb Clip (4)* 8 Halogen Bulb* 9 Wire Guard* 10 Post* 11 Fuse Cap* 12 Fuse (250V, 15A)* 13 Lower Body Assembly* 14 Power Cord* 15 Weight Plate* 16 Inner Support Post * Pre-assembled 4 1 2 14 10 6 9 12 8 13 16 11 5 3 15 7 7 Hardware Tools Required for Assembly (Included) Wrench Nut M10 Nickel Plated 2 pcs A Washer o10 Nickel Plated 1 pc B ® Outdoor Patio Heater Model No. EWTS8119L Assembly Instructions 1 2 Attach Head Assembly DO NOT RETURN PRODUCT TO STORE. Note: Use the wrench to tighten nut. Do NOT over tighten. For assistance call 1.800.762.1142 toll free. Please have your owner’s manual and serial number available for reference. For Easiest Assembly: • To avoid losing any small components or hardware, assemble your product on a hard level surface that does not have cracks or openings. • Clear an area large enough to layout all components and hardware. • When applicable, tighten all hardware connections by hand first. Once the step is completed, go back and fully tighten all hardware. • Follow all steps in order to properly assemble your product. Note: Two (2) adults may be required for assembly. A x 1 3 Attach Base 4 Secure Inner Pole Note: Use the wrench to tighten nut. Do NOT over tighten. A x 1 B x 1 page no. Contact 1.800.762.1142 for assistance. Do not return to place of purchase. Operating Instructions Cleaning and Care (continued) NOTE: Heater functions best WITHOUT an extension cord. Cleaning Surfaces If an extension cord is necessary: 1. Wipe surfaces clean with mild dishwashing detergent or baking soda. • Use a UL approved, 3 prong plug (grounded) cord shall be no. 14 AWG minimum size 2. For stubborn surfaces use a citrus based degreaser and a nylon scrubbing brush. and rated not less than 2,000 watts. 3. Wipe clean with damp cloth. • Never connect two or more extension cords together. Note: While cleaning your unit, be sure to keep the area around the heating element dry at all • Use the shortest extension cord possible. times. Do not submerge the heating element. If the heating element is submerged in water, do NOT use it. It must be replaced. • Keep connections dry and off the ground. • Avoid draping the electric heater cord where children or animals could encounter it. Maintenance Illustration 4 To enjoy years of outstanding performance from Before Turning “ON” your heater, make sure you perform the following 1. Make sure all labels, packaging and protective films have been removed from the heater. maintenance activities on a regular basis: 2. Heater should be thoroughly inspected before each use, and by a qualified service person at 1. Keep exterior surfaces clean. least annually. 2. Air flow must be unobstructed. Keep circulating air passages around th ebulb clean. Turning “ON” Illustration 1 1. Plug the power cord into a dry GFI (Ground Fault Replacing the Fuse Interrupter) 3 plug outlet. (Illustration 1) 1. Push the power button. (Illustration 2) 2. Push the power button. (Illustration 2) 2. Unplug the power cord from the wall outlet. Note: The red LED light will glow while the heater is on. 3. Using a screwdriver, remove the fuse cover. (Illustration 4) Note: When restarting the halogen bulb will start up slowly before getting to full power. 4. Carefully remove the old fuse, and replace with the new fuse. (Illustration 5) Note: ONLY replace the old fuse with a While Heater is ...