Assessments - 1, GPA: 4
(
)
)
|
Facilidade de uso
12. This heater should be thoroughly cleaned on a regular basis. 13. After a period of storage and/or nonuse, check for leaks, burner obstructions and inspect for any abrasion, wear, cuts to the hose. Cleaning Surfaces 1. Wipe surfaces clean with mild dishwashing detergent or baking soda. 2. For stubborn surfaces use a citrus based degreaser and a nylon scrubbing brush. 3. Rinse clean with water. Note: While cleaning your unit, be sure to keep the area around the burner and pilot assembly dry at all times. Do not submerge the control valve assembly. If the gas control is submerged in water, do NOT use it. It must be replaced. Operating Instructions Checking for Leaks Burner Connections 1. Make sure the regulator valve and hose connections are securely fastened to the burner and the tank. 2. If your unit was assembled for you, visually check the connection between the burner pipe and orifice. Make sure the burner pipe fits over the orifice. WARNING: Failure to inspect this connection or follow these instructions could cause a fire or an explosion which can cause death, serious bodily injury, or damage to property. 3. If the burner pipe does not rest flush to the orifice, please contact 1.800.762.1142 for assistance. Tank/Gas Line Connection 1. Make 2-3 oz. of leak solution by mixing one part liquid dishwashing soap with three parts water. 2. Make sure control knobs are “OFF”. 3. Turn LP gas tank valve to “OPEN”. 4. Spoon leak check solution at all “X” locations a. If any bubbles appear turn LP gas tank valve to “CLOSED”, reconnect and re-test. b. If you continue to see bubbles after several attempts, turn LP gas tank valve to “CLOSED” and disconnect LP gas tank and contact 1.800.762.1142 for assistance. b. If no bubbles appear after one minute turn LP gas tank valve to “CLOSED”, wipe away solution and proceed. Before Lighting 1. Heater should be thoroughly inspected before each use, and by a qualified service person at least annually. 2. If relighting a hot heater, always wait at least 5 minutes. 3. Inspect the hose assembly for evidence of excessive abrasion, cuts, or wear. Suspected areas should be leak tested. If the hose leaks, it must be replaced prior to operation. Only use the replacement hose assembly specified by manufacturer. Lighting Note: this heater is equipped with a pilot light that allows for safer startups and shutdowns. Pilot must be lit before main burner can be started. 1. Control knob must be in the “OFF” position. 2. Turn LP gas tank valve to “OPEN”. 3. Open viewing hole by sliding cover to either side. 4. Push control knob in and rotate to “PILOT” position. Note: for initial start or after any tank change, hold control knob in for 2 minutes to purge air from gas lines before proceeding. 5. Push igniter button once. Pilot light flame will appear and be visible through viewing hole. 6. Release control knob after 30 seconds. Pilot light will remain lit. 7. If ignition does not occur, turn control knob “OFF”, wait 5 minutes, and repeat lighting procedure. 8. Turn control knob to “HIGH”. Main burner will light immediately. Flame is visible through viewing hole. If not, turn control knob “OFF”, wait 5 minutes, and repeat lighting procedure. 9. If for some reason your ignitor fails to deliver a spark, your heater can be started by inserting a lit match through the pilot view hole while pushing the control knob in while in the “PILOT” position. WARNING: Be careful when attempting to manually ignite this heater. Holding in the control know for more than 10 seconds before igniting the gas will cause a ball of flame upon ignition. LP Gas Line XLP Gas Tank Valve XXXXXView Hole Proper flame height. Control Knob page no. Contact 1.800.762.1142 for assistance. Do not return to place of purchase. Limited Warranty Cleaning and Care (continued) Maintenance To enjoy years of outstanding performance from your heater, make sure you perform the following maintenance activities on a regular basis: 1. Keep exterior surfaces clean. 2. Air flow must be unobstructed. Keep controls, burner, and circulating air passageways clean. Signs of possible blockage include: Gas odor with extreme yellow tipping of flame. Heater does NOT reach the desired temperature. Heater glow is excessively uneven. Heater makes popping noises. Note: In a salt-air environment (such as near an ocean), corrosion occurs more quickly than normal. Frequently check for corroded areas and repair them promptly. TIP: Use high-quality automobile wax to help maintain the appearance of your heater. Apply to exterior surfaces from the pole down. Do not apply to emitter screen or domes. Storage Between uses: 1. Turn Control Knob OFF. 2. Disconnect LP source. 3. Store heater upright in an area sheltered from direct contact with inclement weather (such as rain, sleet, hail, snow, dust and debris). 4. If desired, cover heater to protect exterior surfaces and to help prevent build up in air passages. Note: Wait until heater is cool before covering. During ...