Assessments - 1, GPA: 4
(
)
)
|
Facilidade de uso
Tools needed: • #2 Phillips screw driver • 7/16 wrench • Needle-nose pliers • Non-abrasive scouring pad • Bottle brush • Pipe cleaners • Air hose or can of compressed air • Rubber gloves DANGERS and Cautions 1. Installation and repair should be done by a qualified service person. 2. Use only Blue Rhino Global Sourcing, LLC. factory authorized parts. The use of any part that is not factory authorized can be dangerous. This will also void your warranty. Contact 1.800.762.1142. 3. Do not use flammable solutions or material to clean heater or heater parts. Use only warm soapy water to clean outside of heater. 4. Do not submerge control valve in water. Cleaning emitter and burner. Series 6000-93000 LP Gas 405121 ®® For assistance call 1.800.762.1142. Steps 1-3 1. Remove propane cylinder. 2. Remove dome. 3. Remove wire guard. Cleaning emitter and burner. Series 6000-93000 LP Gas 405121 ®® For assistance call 1.800.762.1142. Step 4 Using a #2 Phillips screwdriver, remove the 4 screws that secures the emitter to the emitter bottom. Cleaning emitter and burner. Series 6000-93000 LP Gas 405121 ®® For assistance call 1.800.762.1142. Step 5 1. Using a non-abrasive scouring pad, clean the outside and inside of the emitter. 2. Finish up by blowing any loose soot off the emitter with air or a can of compressed air. Cleaning emitter and burner. Series 6000-93000 LP Gas 405121 ®® For assistance call 1.800.762.1142. Step 6 To remove the burner from the emitter bottom unscrew the 2 screws. Cleaning emitter and burner. Series 6000-93000 LP Gas 405121 ®® For assistance call 1.800.762.1142. Step 7 1. In the post, locate the 4 oblong holes. In two of the holes there are 2 small screws. Note: The 2 screws are opposite of each other. 2. Remove both of these screws. Use care not to lose them. Once the screws have been removed, carefully remove burner. Cleaning emitter and burner. Series 6000-93000 LP Gas 405121 ®® For assistance call 1.800.762.1142. Step 8 With the burner removed, clean the inside of the venturi tube. Insert a bottle brush completely into the venturi tube and twist a couple of times to loosen any debris. Cleaning emitter and burner. Series 6000-93000 LP Gas 405121 ®® For assistance call 1.800.762.1142. Step 9 Use a pipe cleaner to clean all burner ports. Clean the top of the heat shield on the burner with a non-abrasive scouring pad to remove any soot or carbon build-up. Cleaning emitter and burner. Series 6000-93000 LP Gas 405121 ®® For assistance call 1.800.762.1142. Step 10 With the venturi tube, burner ports and the heat shield cleaned, use the air or a can of compressed air to blow out any soot or carbon build-up. Cleaning emitter and burner. Series 6000-93000 LP Gas 405121 ®® For assistance call 1.800.762.1142. Step 11 After the burner and the emitter are clean, reassemble the burner to the main supply tube. Be careful to insert the thermal-couple and igniter into the hole in the heat shield. Before reattaching the emitter to the emitter bottom, ins...
Este manual também é adequado para os modelos :Eléctrico - 66000 (1.67 mb)
Eléctrico - 70000 (1.67 mb)