Assessments - 3, GPA: 3.3
(
)
)
|
Facilidade de uso
Store products indoors when not in use – out of the reach of children. Servicing should be done only while the heater is disconnected from the power supply. To ensure continued protection against electrical shock, connect only to properly grounded outlets. Use with GFI protected electric outlet only. Do not immerse in water. Disconnect electric cord from outlet before cleaning, servicing and/or removing heating element. Do not partially or fully cover or obstruct this heater. Please use protective gloves when assembling this product. Do not force parts together as this can result in personal injury or damage to the product. Use this heater only as descibed in this manual. Any other use not recommended by the manufacturer may cause fire, electrical shock, or injury to persons. To reduce risk of shock, keep cord connection dry. Product must be fully assembled before operating the heater. Do not clean this product with a water spray or the like. Deaths, serious injury or damage to property may occur if the above is not followed exactly. page no. Contact 1.800.762.1142 for assistance. Do not return to place of purchase. Parts List Exploded View 1 Finial* 56-01-527 Dome* 56-01-528 Dome Brace* 56-01-529 Insulator* 56-01-496 Upper Pole* 56-01-530 Heat Reflector* 56-01-498 2 3 4 5 6 7 Heating Element Clip (4)* 56-01-499 8 Heating Element* 56-01-500 Wire Guard* 56-01-501 Bottom Guard Plate* 56-01-502 Post* 56-01-531 9 10 11 12 Fuse Cap* 56-01-504 13 Fuse (250V, 15A)* 56-01-505 14 Lower Body Assembly* 56-01-532 Power Cord* 15 16 Inner Support Post 56-01-509 * Pre-assembled 4 1 2 15 11 6 9 8 10 14 5 3 16 7 13 12 7 Hardware Tools Required for Assembly (Included) Wrench Nut M10 Nickel Plated 2 pcs A Washer o10 Nickel Plated 1 pc B ® Outdoor Electric Patio Heater Model No. EWTR800SP Assembly Instructions 1 2 Attach Head Assembly DO NOT RETURN PRODUCT TO STORE. Note: Use the wrench to tighten nut. Do NOT over tighten. For assistance call 1.800.762.1142 toll free. Please have your owner’s manual and serial number available for reference. For Easiest Assembly: • To avoid losing any small components or hardware, assemble your product on a hard level surface that does not have cracks or openings. • Clear an area large enough to layout all components and hardware. • When applicable, tighten all hardware connections by hand first. Once the step is completed, go back and fully tighten all hardware. • Follow all steps in order to properly assemble your product. Note: Two (2) adults may be required for assembly. A x 1 Secure Inner Pole Note: Use the wrench to tighten nut. Do NOT over tighten. 3 A x 1 B x 1 page no. Contact 1.800.762.1142 for assistance. Do not return to place of purchase. Operating Instructions Cleaning and Care (continued) NOTE: Heater functions best WITHOUT an extension cord. Cleaning Surfaces If an extension cord is necessary: 1. Wipe surfaces clean with a solution of water and mild dishwashing detergent or baking soda. • Use a UL approved, 3 prong plug (grounded) cord shall be no. 16 AWG minimum size and rated not less than 1500 watts. 2. Wipe clean with damp cloth. • Never connect two or more extension cords together. Note: While cleaning your unit, be sure to keep the area around the heating element dry at all times. Do not submerge the heating element. If the heating element is submerged in water, do • Use the shortest extension cord possible. NOT use it. It must be replaced. • Keep connections dry and off the ground. • Avoid draping the electric heater cord where children or animals could encounter it. Maintenance Illustration 4 To enjoy years of outstanding performance from Before Turning “ON” your heater, make sure you perform the following maintenance activities on a regular basis: 1. Make sure all labels, packaging and protective films have been removed from the heater. 1. Keep exterior surfaces clean. 2. Heater should be thoroughly inspected before each use, and by a qualified service person at least annually. 2. Air flow must be unobstructed. Keep circulating air passages around the heating element clean. Turning “ON” Illustration 1 Replacing the Fuse 1. Plug the power cord into a dry GFI (Ground Fault Interrupter) 3 plug outlet. (Illustration 1) 1. Push the power button. (Illustration 2) 2. Push the power button. (Illustration 2) 2. Unplug the power cord from the wall outlet. Note: The red LED light will glow while the heater 3. Using a screwdriver, remove the fuse cover. is on. (Illustration 4) Note: When restarting the heating element will start up 4. Carefully remove the old fuse, and replace with the slowly before getting to full power. new fuse. (Illustration 5) Note: ONLY replace the old fuse with a While Heater is “ON” 250V 15A fuse. If heater tips over, the heater will automatically 5. Reattach the fuse cover. turn “OFF”. Note: Do not over tighten If heater tips over: 6. Follow the Turning “ON” instructions or the Storage 1. IMMEDIATLEY unplug power cord from the wall outlet. Instructions. 2...