Assessments - 3, GPA: 3.3 ( )

Fabricante : Storageflex Arquivo Tamanho: 585.79 kb Arquivo Nome : Língua de Ensino:

Caution: If you install the heater in a home garage: • Heater must be at least 18” above floor • Locate heater where moving vehicle will not hit it. • Install to ANSI Z223.2 / NFPA 54 using fixed gas supply piping. PREPARING FOR INSTALLATION 1. Remove heater from carton 2. Remove all protective packaging applied to heater for shipment. 3. Check heater for any shipping damage. If heater is damaged, promptly inform dealer/distributor. 4. Select a location for the heater that will provide maximum exposure of the radiant surface to the room, but will not be subjected to accidental contact. 5. Adequate clearance must be available around the air opening. Refer to Figure 2 for clearances that must be maintained to the side walls, floor and horizontal surface surrounding the heater. Fig. 2 Minimum clearances from mounting holes to top surface of flooring, adjacent walls and ceiling ATTACH MOUNTING SCREWS TO WALL NOTE: Wall anchors and mounting screws are in hardware package provided with heater. 1. Install mounting screws on wall as shown in Figure 3. Use enclosed paper template for proper location of holes. Be sure template is level. It may be necessary to use plastic or lead anchors for plaster walls. 2. Drill holes at marked location using 9/64” drill bit. Insert mounting screws. 3. Leave screw head out from wall far enough to attach heater. Fig. 3 Use paper template supplied to mark location of mounting holes. Be sure template is level. FLOOR INSTALLATION WALL ANCHOR METHOD FLOOR INSTALLATION WALL ANCHOR METHOD When mounting heater to hollow walls (wall areas between studs) or solid walls (concrete or masonry) it may be necessary to use wall anchors. 1. Place paper template on wall maintaining minimum clearance. Be sure template is level. 2. Drill holes at marked locations using 5/16”drill bit. For solid walls, concrete or masonry, drill holes at least 1”deep. 3. Insert plastic anchor. Tap anchor flush to wall. (Fig. 4) 4. Insert screw into wall anchor leaving screw head out far enough to attach heater. (Fig. 4) 5. Hang heater on mounting screws in holes provided at the rear of the heater. 1. Heater may only be installed on a noncombustible flat surface. Where the flooring is carpeting, tile or of other combustible material other than wood flooring, maintain the minimum clearances to the floor as shown in figure 2 or else use a metal or wood panel (not supplied) extending the full width and depth of the appliance. 2. Measure heater mounting screw location “X” as desired above floor. (Fig. 5) 3. Use enclosed “paper template” for proper distance between holes. Be sure template is level. It maybe necessary to use plastic or lead anchors for plaster walls. 4. Leave screw head out from wall far enough to attach heater. Fig. 4 Wall anchor. x = 173/4" 45 CM 30,000 BTU/hr units 161/2" 42 CM 18 & 20,000 BTU/hr units 141/4" 36 CM 6 & 10,000 BTU/hr units Fig. 5 Optional wall mounting screws for floor installation. CONNECT TO GAS SUPPLY CONNECT TO GAS SUPPLY PRESSURE TEST GAS SUPPLY PIPING SYSTEM Installation should be done by a qualified service person. Before connecting the appliance, turn off all gas appliances. Close the main gas valve at the gas meter or LP tank. Make certain there is good ventilation where the installation will be made. Installation should comply with all applicable building codes and ANSI Z223.1, latest edition. Use PLP gas resistant pipe compound to seal threaded joints. An installer supplied, design certified gas pressure regulator must be installed to bring the gas supply pressure down to 14" w.c. for LP gas or 11" for natural gas. WARNING: Never connect an unregulated gas line to the heater. IMPORTANT: Check gas line pressure before connecting heater to gas line. Gas line pressure must not be higher higher than 14" w.c. for LP gas or 11" for natural gas. NOTE: The gas line connection can be made with 3/8”black or steel pipe. Internally tinned copper tubing may be used in certain areas. Check your local codes. Use pipe of large enough diameter to allow proper gas volume to heater. If pipe is too small, undue pressure loss will occur. CAUTION: Use pipe joint sealant that is resistant to liquefied petroleum gases. Install sediment trap in supply as shown in Figure 6. Locate sediment trap where it is within reach for cleaning. Locate sediment trap where matter is not likely to freeze. A sediment trap prevents moisture and contaminant's from going into the heater controls. If the sediment trap is not installed or is installed wrong, the heater may not operate properly. Test for gas leaks with a mild soap and water solution. Apply water/soap solution with brush only - do not over apply. NEVER test with an open flame. The appliance and its individual shut off (control) valve must be disconnected from the gas supply piping system during any pressure testing of the system at test pressure in excess of 1/2 psi (3.5 kPa). The appliance must be isolated from the gas supply piping system by closing the indiv...

Baixe o seu

Para fazer o download, introduza 2 dígitos :