Assessments - 3, GPA: 3.3
(
)
)
|
Facilidade de uso
If millivolt output decreases during furnace operation gas control may be defective. Main Gas Valve Does Not Open When Thermostat Is Turned "On" 1. Check millivolt output of thermopile. 2. Thermostat wires may be broken. 3. Thermostat may be defective. Page 14 12425-10-1008 PARTS LIST ATTENTION: When ordering parts, it is very important that part number and description of part coincide. Index No. Part No. Description 1 WFA-115 HEADER GASKET 2 GWT-175 HEADER ASSEMBLY (INCLUDES NO. 1, GASKET) (USA) 2 15740 HEADER ASSEMBLY (INCLUDES NO. 1, GASKET) (CANADA) 3 GWT-182 INNER CASING ASSEMBLY 4 GWT-065 DIVERTER ASSEMBLY- GWT-25-2 4 GWT-066 DIVERTER ASSEMBLY - GWT-35-2 5 R-3239 VENT SAFETY SWITCH - GWT-25-2 5 R-3045 VENT SAFETY SWITCH - GWT-35-2 6 R-3038-A ECO LEAD ASSEMBLY 7 GWT-020 FRONT SHIELD 8 GWT-077 HEAT SHIELD 9 GWT-068 EXCHANGER ASSEMBLY - GWT-25-2 9 GWT-069 EXCHANGER ASSEMBLY- GWT-35-2 10 GWT-070 BURNER BRACKET ASSEMBLY - GWT-25-2 10 GWT-073 BURNER BRACKET ASSEMBLY - GWT-35-2 11 R-5245 GAS VALVE - NAT 11 R-5246 GAS VALVE - LP 12 R-3031 BURNER (GWT-25-2 – 3 REQUIRED) (GWT-35-2 – 4 REQUIRED) 13 P-88-55 BURNER ORIFICE - GWT-25-2 NAT (3 REQUIRED) 13 P-88-65 BURNER ORIFICE - GWT-25-2 LP (3 REQUIRED) 13 P-88-54 BURNER ORIFICE - GWT-35-2 NAT (4 REQUIRED) 13 P-88-65 BURNER ORIFICE - GWT-35-2 LP (4 REQUIRED) 14 GWT-015 AIR SHUTTER REAR- GWT-25-2 LPG Index No. Part No. Description 14 GWT-012 AIR SHUTTER REAR - GWT-35-2 LPG 15 GWT-054 AIR SHUTTER BOTTOM - GWT-25-2 LP 15 GWT-049 AIR SHUTTER BOTTOM - GWT-35-2 LP 16 GWT-014 AIR SHUTTER FRONT - GWT-25-2 LP 16 GWT-011 AIR SHUTTER FRONT - GWT-35-2 LP 17 GWT-010 BURNER COMPARTMENT FRONT - GWT-25-2 17 GWT-008 BURNER COMPARTMENT FRONT - GWT-35-2 18 DV-064 COVER PLATE 19 R-3035 PILOT - LP 19 R-3034 PILOT - NAT 20 GWT-021 PILOT BRACKET 21 R-1054 THERMOPILE 22 GWT-186 CASING BRACKET 23 GWT-177 CASING FRONT ASSEMBLY (INCLUDES #24) 24 R-3763 MAGNET (2 REQUIRED) 25 GWT-087 CASING DOOR ASSEMBLY (USA) 25 15739 CASING DOOR ASSEMBLY (CANADA) 26 R-885 NYLON WASHER (2 REQUIRED) 27 17508 VALVE SHIELD 28 23385 CASING ASSEMBLY COMPLETE (INCLUDES #23, #25, & #26) N/S GWT-121 PILOT TUBING- GWT-25-2 N/S GWT-076 PILOT TUBING- GWT-35-2 N/S R-1089 PILOT ORIFICE (HONEYWELL .009 LP ONLY) N/S R-1081 PILOT ORIFICE (HONEYWELL .014 NAT ONLY) N/S GWT-190 HARDWARE PACKAGE USE ONLY MANUFACTURER'S REPLACEMENT PARTS. USE OF ANY OTHER PARTS COULD CAUSE INJURY OR DEATH. HOW TO ORDER REPAIR PARTS Parts can be ordered only through your service person or dealer. For best results, the service person or dealer should order parts through the distributor. Parts can be shipped directly to the service person/dealer. All parts listed in the Parts List have a Part Number. When ordering parts, first obtain the Model Number from the name plate on your equipment. Then determine the Part Number (not the Index Number) and the Description of each part from the following appropriate illustration and list. Be sure to give all this information. Furnace Model Number Part Description Furnace Serial Number Part Number Type of Gas (Propane or Natural) Do not order bolts, screws, washers or nuts. They are standard hardware items and can be purchased at any local hardware store. Shipments contingent upon strikes, fires and all causes beyond our control. 12425-10-1008 Page 15 Page 16 12425-10-1008 PARTS VIEW REMOTE BULB CONTROL INSTALLATION INSTRUCTIONS MODELS GWT-25 RB, GWT-35 RB, GWT-50 RB Index Part No. Number Description 1 GW-130 Remote Bulb Control Kit 2 R-1224 Remote Bulb Control 3 R-2499 Wire Assembly 4 R-1162 Control Knob 5 R-1720 Plastic Clip (3 Required) 6 R-1223 Instructions 7 R-1578 No. 6-32 x 1/4" (6mm) Screw (2 Required) INSTRUCTIONS Note: At the option of the owner, the remote bulb control may be located on the left or right side of the outer casing. 1. Remove remote bulb control from the shipping carton. 2. Remove outer casing assembly from shipping carton. Note: If wall furnace is already installed, remove outer casing from unit and lay on floor with front side down. 3. Attach wire assembly to remote bulb control. 4. Carefully unwind capillary wire on remote bulb control. 5. Remove (3) hole plugs from left or right side of outer casing where remote bulb control is to be installed. 6. Mount remote bulb control to inside of outer casing with (2) No. 6-32 x 1/4" (6mm) screws. Caution: Remote bulb wire routing is important. Wires should be in proper location to avoid damage from being overheated. Incorrect routing of remote bulb control wires may result in damage to wires and incorrect operation of remote bulb control. Follow these instructions and refer to the drawing for proper wire routing. 7. If remote bulb control is located on the right side of the outer casing, carefully bend or loop capillary wire around control. This will enable the sensing bulb to be positioned at the bottom of the unit. 8. Secure sensing bulb on the inside, at the bottom, of the outer casing with (2) plastics clips. 9. Feed the wire assembly dow...
Este manual também é adequado para os modelos :Eléctrico - GWT-25-2(SG (3.9 mb)
Eléctrico - GWT-35-2(SG (3.9 mb)