Assessments - 3, GPA: 3.7
(
)
)
|
Facilidade de uso
¦ Lift cover while installing ¦ Complete installation. remaining cylinder cover section. Mantles ¦ Remove 2 glass panels. ¦ Slip mantle onto burners. Align clips in mantle with groove in burner. Be sure clip points away from electrode. Electrode Groove ¦ Twist clips. Mantles continued. ¦ Attach second mantle. Illustration below shows proper assembly of both mantles. ¦ Light bottom of mantles evenly. Burn until nothing but white ash remains. Once mantle has been burned it’s very fragile. Be careful not to touch it with a finger or match. Install glass panels. Battery Installation for HEATER ¦ Unscrew igniter button to reveal battery compartment. ¦ Install AA battery with positive (+) outward. ¦ Replace igniter button finger tight. 10 Operation DANGER • CARBON MONOXIDE HAZARD • For outdoor use only. Never use inside house, or other unventilated or enclosed areas. This heater consumes air (oxygen). Do not use in unventilated or enclosed areas to avoid endangering your life. DANGER • EXPLOSION - FIRE HAZARD • Never store propane near high heat, open flames, pilot lights, direct sunlight, other ignition sources or where temperatures exceed 120 degrees F (49°C). • Propane is heavier than air and can accumulate in low places. If you smell gas, leave the area immediately. • Never install or remove propane tank while heater is lighted, near flame, pilot lights, other ignition sources or while heater is hot to touch. • This heater is red hot during use and can ignite flammables too close to the burner. Keep flammables at least 3 feet from sides & 2 feet from top. Keep gasoline and other flammable liquids and vapors well away from heater. • The propane tank must always be stored outdoors in a well ventilated space. Never store propane tank in an enclosed area (house, garage, etc.). If heater is to be stored indoors, disconnect the propane tank for outdoor storage. • Do not attempt to operate until you have read & understand all General Safety Information in this manual and all assembly is complete & leak checks have been performed. Lighting Instructions for HEATER ¦ Turn cylinder valve on. 1. Push in and rotate (counter clockwise) heater control knob to the Pilot position and release. 2. Push in on heater control knob and push Igniter Button to ignite Pilot Light. Note:Initial lighting after gas cylinder change can take up to two (2) minutes to purge any air that may be in the line. Operation continued. Match Lighting Instructions for HEATER 1. Turn cylinder valve on. 2. Push in and rotate (counter clockwise) Heater Control Knob to the Pilot position and release. 3. Use a long match. Locate Pilot Port directly above center glass panel. 4. Light a long fireplace match (minimum 4" long) and insert into Pilot Port, then push in and hold Heater Control Knob. 5. Pilot light will ignite and be visible from Pilot Port or Pilot Viewing Port. Continue to push Heater Control Knob in for 30 to 60 seconds after pilot is on, then release knob. Pilot light must remain on, if not return to Step 1. Pilot Port Note:If pilot fails to remain lighted, all valves should be closed and a waiting period of at least 5minutes should pass before attempting to light. 6. Rotate Heater Control Knob to ON position. Heater burner will light and be visible through screen of heater. If Heater burner does not light, turn off Heater Control Knob and return to Step 1. 11Lighting Instructions for HEATER continued. Lighting Instructions for LIGHT Note:If pilot fails to remain lighted, all valves should be closed and a waiting period of at least 5minutes should pass before attempting to light. 4. Rotate Heater Control Knob to ON position. Heater burner will light and be visible through screen of heater. If Main burner does not light, turn off Heater Control Knob and return to Step 1. 3. Pilot Light will ignite and be visible through Pilot Viewing Port (flame may be difficult to see in broad daylight). Continue to push Heater Control Knob in for 30 to 60 seconds after pilot is on, then release knob. Pilot Light must remain on, if not return to step 1. Heater Control Knob Igniter Igniter Light Control Knob 1. Push in and rotate Light Control Knob to the ON position while pushing the Igniter Button until BOTH mantles are lighted. Note:If BOTH mantles are not lighted within 5 seconds, turn Light Control Knob to OFFposition.All controls should be turned to the OFF position and a period of at least 5 minutes should pass before reattempting to light burners. 2. Mantles will light and begin to glow which can be seen through the windows. If the mantles do not light or fail to remain lighted turn OFF Light Control Knob and return to Step 1. ¦ Unit can be operated with heater & light both operating or either operating separately. Pilot Port Pilot Viewing Port Operation continued. Shut Down Procedure Match Lighting Instructions for LIGHT 1. Turn cylinder valve on. 2. Remove front glass. 3. Place a lighted match near mantle, then push in and rotate Light Control Knob to...
Este manual também é adequado para os modelos :Eléctrico - 5040-761 (820.36 kb)