Assessments - 3, GPA: 4
(
)
)
|
Facilidade de uso
Use the buttons again to set the minutes. Scroll up or down using the buttons until the correct time is reached. Press the TIMER SET button five times to lock in the time. The CLOCK and TIMER indicators will go out. A small indicator on the digital display will flash to show that the clock is operating. • TIMERS / PREHEAT This heater has two programmable timers, these allow you to set a start and finish time. The temperature is preset each time the timers are activated. There is also a preheat function that measures the temperature of the room and estimates the time it will take to bring the room up to the preset temperature by the programmed start time. This means that the heater may start heating an hour or more before the programmed start time. • PROGRAMMING THE ON / OFF TIMERS Before programming the Timers you must ensure that the clock has been set to the correct time. Press the SET TIMES button twice. The digital display will show AM 6:00 and the TIMER 1 - ON indicator will flash. Set the desired start time the same way as for setting the clock. Be aware that the heater may start up much earlier than the programmed start time due to the preheat function, as explained earlier. Press the SET TIMES button again, the TIMER 1 - OFF indicator will flash. Set the desired stop time the same way as for setting the clock. Press the SET TIMES button once to 10 proceed to TIMER 2 - which is again when the power comes back on, but programmed in the same way - or three the time will be slow by the duration of the times to return to the clock display. This power failure. To set the clock to the must be done within 1 minute of setting the correct time after the power has come time to lock it into the memory. back on, simply follow the instructions on page 9. The digital display will show the current time. A small indicator on the digital display • OVERRIDE will flash to show that the display has This function is intended to be used to returned to the clock. manually override the current operation of After setting timer 2 the SET TIMES button the heater. For example; If the heater is in must be pressed once within one minute stand-by mode (ie. between finishing time of programming to lock in the times and and starting time of a timer), and the return to the clock display. OVERRIDE button is selected, then the heater will begin to operate and heat the The timers operate over a 24 hour period, room. and will activate 7 days a week when set. Press the OVERRIDE button to activate. • OPERATING THE TIMERS The indicator light will flash when active. Before operating the timer(s), the clock To manually deactivate the OVERRIDE time must be correct and a starting time press the OVERRIDE button again. The and finishing time for the timer(s) must be OVERRIDE indicator will go out, and the programmed, see page 9. Both timers heater will return to stand-by mode. operate in the same way. The heater will continue to operate on Ignite the heater and select the preset OVERRIDE until the OVERRIDE button is temperature as for normal operation. pressed again, or one of the timers takes Press the timer 1 and / or timer 2 button(s). over the operation of the heater. This The timer indicator(s) will glow and the unit means that the OVERRIDE mode will will change to stand-by mode. The burners automatically turn off if a programmed will extinguish and the ON indicator will starting time is reached. The heater will change from red to green. The display will then return to operating at times show the start time for the selected timer programmed into the timer(s). Turning the briefly before returning to the clock display. heater off will also deactivate the OVERRIDE. When the heater is in stand-bys mode, you can display and change the clock and the • REMOTE CONTROL on and off times for both timers in the same The remote control can only be used for way as described earlier. manual operation of the heater. If the The timers can be deactivated by either heater is in stand-by (timer) mode then only pressing the timer button(s) that you want the OFF button will work. Pressing the OFF to deactivate or by turning the heater off button when the heater is in stand-by mode using the ON/OFF button. will deactivate the timers and the heater can now be operated manually. NOTE: If there is a power failure, the system memory will retain the Timer The ON and OFF buttons on the remote programs, and the clock will stop at the work in the same way as the ON / OFF “ time the power goes off. The clock will start button on the control panel as do the “ and “ “ buttons. 11 ON BUTTON Operates the unit manually. OFF BUTTON Stops unit manually. TEMPERATURE ADJUSTMENT Increases or decreases the temperature setting. • TO REPLACE REMOTE CONTROL BATTERY The battery is held in a clip that slides out the bottom of the remote control. The clip is removed by inserting a coin or similar into the recess in the back of the remote control and sliding downwards. The battery must be o...
Este manual também é adequado para os modelos :Eléctrico - IB35ETRLC (652.29 kb)