Assessments - 5, GPA: 3.8 ( )

Fabricante : Well Traveled Living Arquivo Tamanho: 1.59 mb Arquivo Nome : Língua de Ensino:

Loosen and re-tighten this connection. 6) If leak continues call a qualified service person. 7) Use of teflon (plumber’s) tape on threads of gas connections is recommended. Well Traveled ► ASSEMBLY Step11 — Lower Cylinder Cover onto Cylinder Base Lower the cylinder cover onto the cylinder base. Step12— Disconnect Cylinder When Storing orTransporting 1). Turnoff the heater. 2). Turnoff the valve of thecylinder. 3). Lift the cylinder cover above the post mounts. 4). Loosen the screw of cylinderand regulator. 5). Disconnect thecylinder from regulator. Well Traveled Step 11 11 The installation must conform with local codes or, in the absence of local codes, with the most current version of the National Fuel Gas Code, ANSI Z223.1 OPERATION WARNING: Do NOT attempt to operate heater until you have read and understood all precautions. Failure to do so can result in serious personal injury, death and/or property damage. Before Turning Gas Supply ON Your heater was designed and approved for OUTDOOR USE ONLY. Do NOT use it inside a building ,or any other enclosed area. Make sure surrounding areas are free of combustible materials, gasoline and other flammable vapors or liquids. Ensure that there is no obstruction to air ventilation. Be sure all gas connections are tight and there are no leaks. Be sure the access panel is clear of debris. Be sure any component removed during assembly or servicing is replaced and fastened prior to starting. Before Lighting Heater should be thoroughly inspected before each use, and by a qualified service person at least annually. If relighting a hot heater, always wait at least 5 minutes. Our heater is tested for quality assurance. Ignition attempts should succeed 8 out of 10 attempts. LIGHTING INSTRUCTIONS 1) Turn the control knob to "OFF" position. 2) Fully open gas valve 3) Push in gas control knob and turn counterclockwise to "IGNITE" then to "PILOT" position, this will light the pilot. If needed, keep depressing and turning control knob counterclockwise until the pilot lights.(You will hear 2 clicking noises) 4) Once the pilot is lit, continue to keep the control knob depressed for at least 30 seconds, After 30 seconds release control knob. 5) If pilot does not stay lit, repeat steps 3 and 4. 6) If pilot still does not stay lit, then: a) Push in gas control knob and turn counterclockwise to "IGNITE" then to "PILOT” b) Keep depressing the control knob. Put long stem lighter into the Ignition Hole on the emitter screen to light the pilot. c) Repeat step 4. 7) Push in and turn control knob counterclockwise to "LOW" position, release knob then turn to low. If you want a higher temperature, push in the control knob and turn counterclockwise to the "HIGH" position. Note: The flame pattern at the emitter grid should be visually checked whenever heater is operated. Normally the burner flame is blue, but a little yellow flame is acceptable. If flames extend beyond the emitter grid or there are black spots that have accumulated on the emitter grid or reflector, immediately turn off the patio heater. The heater should not be operated again until it has been serviced and repaired by a qualified gas technician. If you experience any ignition problem, turn off the heater and gas supply, and consult "Troubleshooting" on page17. Well Traveled WARNING FOR YOUR SAFETY: Do NOT touch or move heater for at least 45 minutes after use. Allow emitter and dome to cool before touching. WARNING FOR YOUR SAFETY: Ifatany time you are unable to lightburner and smell gas, wait 5 minutes to allow gas to dissipate before attempting to light heater. If, after 1 minute, you are unable to light burner, wait 5 minutes and allow flammable vapors to dissipate before attempting to light heater again. 12 OPERATION CAUTION : Avoid inhaling fumes emitted from the heater’s first use. Smoke and odor from the burning of oils used in manufacturing will appear. Both smoke and odor will dissipate after approximately 30 minutes. The heater should NOT produce thick black smoke. NOTE: The burner may be noisy when initially turned on. To eliminate excessive noise from the burner, turn the Control Knob to the" LOW" position. Then, turn the knob to the level of heat desired. When heater is ON: Emitter screen will become bright red due to intense heat. The color is more visible at night. Burner will display tongues of blue flame. These flames should not be yellow or produce thick black smoke, indicating an obstruction of airflow through the burners. Operation Pressure Checked If the flame is very small, this is because the supply pressure is not enough. To Light 1)Turn the control knobto"OFF" position. 2)Wait five (5) minutes before attempting to relight pilot. 3) Repeat steps beginning with step 2 on page 12. Before Leaving 1 )Turn the control knob to "OFF" position and Turn LP cylinder to "OFF" position. 2)Never leave the patio heater unattended while in use. SHUT DOWN...

Baixe o seu

Para fazer o download, introduza 2 dígitos :