Assessments - 3, GPA: 4
(
)
)
|
Facilidade de uso
9. Remote: Credit card size with large buttons. Operation Turning Power On 1. Press the Power button on the left side of the Control Panel. The heater’s quartz heating elements will light up inside the heater. 2. After a few minutes, once the air within the heater is warm, the heater fan (some models have 2) will begin to operate. Turning Power Off 1. Press the Power button located on the left side of the Control Panel. 2. The sound of the heater fan will continue until the heat has been completely vented, thus protecting the unit and preventing waste by cycling the remaining heat into the room. (DO NOT unplug the heater until the sound of the fan has stopped. Doing so may cause damage to the unit.) Setting the Temperature This feature allows you to set the temperature measured by the units thermostat. 1. Press the Temperature (TEMP) Button on the Control Panel; the Set Temp Indicator will illuminate and the temperature display will flash. 2. Use the Up and Down buttons to select the temperature and press Enter. 3. The Set Temp light will turn off and the temperature is now set. Setting the Timer This feature allows you to set a future time for the heater to turn itself ON. For example, if you set the time for 1 hour, the heater will turn ON in 1 hour. 1. Turn the Power OFF (heater must be powered OFF to use the timer feature). DELAY STARTSET TEMPINFRARED-ONDELAY STARTSET TEMPINFRARED-ONDELAY 2. Press the Time button of the Control Panel - the two zeros to the right will flash (:00), indicating 0 minutes have been set and the DELAY START indicator will illuminate. 3. Press the UP or DOWN button to select desired number of minutes (up to 59 minutes) that you would like the heater to wait to turn itself on. 4. Press the ENTER button - the two zero button to the left will flash (00:), indicating 0 hours have been set. 5. Press the UP or DOWN button to the desired number of hours (up to 24 hours) and then press the ENTER button. 6. DELAY START indicator will flash until the unit comes on after waiting the period of time you have set. 7. To cancel the timer, press the power button and the timer will stop. Switching between Fahrenheit & Celsius Press the DOWN & ENTER buttons simultaneously and hold for about 3 seconds. The display will update automatically. ONDELAY STARTSET TEMPINFRARED-ONDELAY STARTSET TEMPINFRARED-ON Operation Suggestions for Best Performance To assure maximum performance of your Oreck Heatwise™ Infrared Heater, please review the following recommendations: • Do not locate the heater in an area with a high air exchange rate in and out of the room. Heat produced should be contained in the room. • Try placing the heater near a warmer inside wall and direct the output toward a cooler outside wall. The cooler outside wall will tend to draw the generated heat towards it, which will allow for more efficient heating. • Placing the heater next to a cord air return will draw the heat away from the area to be heated. Try closing or covering the cold air return. This will alow for more efficient heating. Experiment with the placement of the heater to see what works best for you. • To ensure maximum efficiency, a 30% minimum relative humidity should be maintained in the heated environment. • The heater is designed to operate for maximum efficiency in the 68-74 degree range. Due to the soft heat concept, temperatures at 68 degrees F feel as though it were 72 degrees F. This is due to the heat mixing with humidity evenly for head-to-toe comfort. • When the heater is placed in an isolated area, i.e. basement or recreation area, any existing HVAC heating system vents should be closed in that area, if possible. This allows the heater to maintain the isolated area more efficiently. • If placing the heater a few feet above the floor, such in rooms with large areas of bare concrete, make sure the heater is secure and won’t fall. This will allow for more efficient heating since concrete acts as a heat sink and will tend to draw the heat in its direction. Optimally, concrete floors should be covered to provide some insulation factor from the concrete. • For zone heating: set your central heating system to a lower temperature. Place the heater in the area you spend the most of your time. Now set the heater to your comfort level. • When heating larger areas, place the heater in a central location. • If the heater is used in an extremely dirty area, the filter must be cleaned more frequently to maintain heater performance. Operation Maintenance The only maintenance that is required for the heater is the periodic cleaning of the heater’s electrostatic filter (located at the back of the unit). This cleaning should be performed at least once a month, or earlier as dust becomes visible on the filter, to ensure efficient operation of the heater. Cleaning the Electrostatic Filter Clean the filter often to provide for maximum performance. When necessary, wipe the cabinet clean with a soft damp cloth and/or furniture polish. 1....
Este manual também é adequado para os modelos :Eléctrico - HEATWISE HW1500P (2.03 mb)
Eléctrico - HEATWISE HW1500W (2.03 mb)