Assessments - 4, GPA: 3.5 ( )

Fabricante : Homelite Arquivo Tamanho: 281.28 kb Arquivo Nome : Língua de Ensino:

Plug extension cord into standard 120 volt/60 hertz, three-hole, grounded outlet. Heater will start when extension cord is plugged into outlet. If not, push in flame-out control reset button (see Figures 5 and 6). To Stop Heater Unplug extension cord from outlet. To Restart Heater 1. Wait 2 minutes after stopping heater. 2. Repeat steps under To Start Heater. Flame-Out Control Reset Button Flame- Out Control Reset Button Figure 6 - Flame-Out Control Reset Button, 110/150,000 BTU/Hr Models Figure 5 - Flame-Out Control Reset Button, 35/55,000 BTU/Hr Models 100507 5 PORTABLE SPACE HEATER STORING, TRANSPORTING, OR SHIPPING PREVENTATIVE MAINTENANCE SCHEDULENote: If shipping, transport companies re WARNING: Never service heater while it is plugged in, operating, or hot. Severe burns and electrical shock can occur. quire fuel tanks to be empty. 1. Drain fuel tank. Note: Some models have drain plug on underside of fuel tank. If so, remove drain plug to drain all fuel. If heater does not have drain plug, drain fuel through fuel cap opening. Be sure all fuel is removed. 2. Replace drain plug if provided. 3. If any debris is noted in old fuel, add 1 or 2 quarts of clean kerosene to tank, stir, and drain again. This will prevent excess debris from clogging filters during future use. 4. Replace fuel cap or drain plug. Properly dispose of old and dirty fuel. Check with local automotive service stations that recycle oil. 5. If storing, store heater in dry place. Make sure storage place is free of dust and corrosive fumes. IMPORTANT: Do not store kerosene over summer months for use during next heating season. Using old fuel could damage heater. Item How Often How To Fuel tank Flush every 150-200 hours of operation or as needed. See Storing, Transporting, or Shipping, column 1. Air output and lint filters Replace every 500 hours of operation or once a year. See Air Output, Air Intake, and Lint Filters, page 8. Air intake filter Wash and dry with soap and water every 500 hours of operation or replace as needed. See Air Output, Air Intake, and Lint Filters, page 8 Fuel filter Clean twice a heating season or replace as needed. See Fuel Filter, page 9 Spark plug Clean and regap every 600 hours operation or replace as needed. See Spark Plug, page 10 Fan blades Clean each season or as needed See Fan, page 8. Motor Not required/permanently lubricated 6 OWNER’S MANUAL TROUBLESHOOTING WARNING: Never service heater while it is plugged in, operating, or hot. Severe burns and electrical shock can occur. OBSERVED FAULT POSSIBLE CAUSE REMEDY Heater ignites, but flame-out control shuts 1. Wrong pump pressure 1. See Pump Pressure Adjustment, page 9 off heater after a short period of time. 2. Dirty air output, air intake and lint filters 2. See Air Output, Air Intake and Lint Filters, page 8 3. Dirty fuel filter 3. See Fuel Filter, page 9 4. Dirt in nozzle 4. See Nozzle, page 11 5. Dirty photocell lens 5. Clean photocell lens 6. Bad flame-out control 6. Replace flame-out control WARNING: Disconnect heater cord! Heater will not ignite, but motor runs for a 1. Wrong pump pressure. 1. See Pump Pressure Adjustment, page 9 short period of time. 2. Carbon deposits on spark plug and/or 2. See Spark Plug, page 10 improper gap 3. Dirty fuel filter 3. See Fuel Filter, page 9 4. Dirt in nozzle 4. See Nozzle, page 11 5. Water in fuel tank 5. Drain and flush fuel tank with clean kerosene. See Storing, Transporting, or Shipping, page 6. WARNING: High Voltage! 6. Electronic ignitor not grounded 7. Bad electronic ignitor 6. Make sure electronic ignitor mounting is tight. 7. Replace electronic ignitor. Motor does not start when heater is plugged in, fan rotates slowly or does not turn. 1. Flame-out control not reset 2. Solid state relay not allowed to reset 3. Binding pump rotor 1. Press flame-out control reset button. 2. Wait two minutes before trying to restart heater. 3. If fan is hard to turn, see Pump Rotor, page 12. 7 8 100507 PORTABLE SPACE HEATER SERVICE PROCEDURES Air Output Filter Lint Filter Air Intake Filter Filter End Cover Air Output Filter Lint Filter Air Intake Filter Filter End Cover Fan Guard Figure 11 - Air Output, Air Intake, and Lint Filters, 35/55,000 BTU/Hr Models Figure 12 - Air Output, Air Intake, and Lint Filters, 110/150,000 BTU/Hr Models Fan Guard UPPER SHELL REMOVAL 1. Remove screws along each side of heater using 5/16" nut-driver. These screws attach upper and lower shells together. 2. Lift upper shell off. 3. Remove fan guard. Upper Shell Fan Guard Upper Shell Fan Guard Figure 7 - Upper Shell Removal, 35/55,000 BTU/Hr Models Figure 8 - Upper Shell Removal, 110/150,000 BTU/Hr Models Figure 9 - Fan Cross Section 35/55/110,000 BTU/Hr Models Figure 10 - Fan Cross Section 150,000 BTU/Hr Model Fan Fan Setscrew Motor Shaft Motor Flush Motor Shaft Back of Flat Surface on Motor Shaft Setscrew Motor WARNING: Never service heater while it is plugged in, operating, or hot. Severe burns and electrical shock can occur. AIR OUTPUT, AIR INTAK...

Baixe o seu

Para fazer o download, introduza 2 dígitos :