Log:
Assessments - 2, GPA: 3.5 ( )

Instruções de Operação Cadet, Modelo C152

Fabricante : Cadet
Arquivo Tamanho: 147.71 kb
Arquivo Nome :
Língua de Ensino: en
Ir para baixar



Facilidade de uso


Owner’s Guides may be downloaded at SAVETHESEINSTRUCTIONS Tel: 360-693-2505 P.O. Box 1675 Vancouver, WA 98668-1675 InstallationInstructionsInstallationInstructions 1. Remove knob (if applicable) and screws to remove grill. 2. Remove grill. 3. Remove heatbox from wall can by loosening screw at top. 4. Unwiring A. Remove insulated wire connectors that connect heatbox to wall can. B. Cut as many wire ties on back of heater as necessary for easier accessibility. C. Cut reset wires coming out of lower 5/16” pass through hole on back of heatbox. (See Figure 1) 5. Turn heater upward, remove screw at the bottom of face cover, just above thermostat location. 6. Lift face from bottom and slide over tab on top of box. Set motor and element assembly aside. 7. Turn face cover so reset limit and wires are facing you. Carefully unclamp contact point tabs using a flathead screwdriver (See Figure 2). 8. Twist tabs that reset approximately 90 degrees. This will allow the reset to easily slip out of place (See Figure 3). 9. Bend both tabs to original position. Snap new reset in place. 10. Place copper wire in contact point tabs as shown in Figure 2. Clamp wire in place with pliers, being careful not to damage, kink or cut copper wire. Be sure capillary tube (limit tubing) lays flat against cover. (See Figure 2) 11. Feed wires back through 5/16” hole of motor and element assembly, making sure to take out all slack. (See Figure 1) 12. Replace face cover over tab on top. Be sure to hold wires and snap in place. LOWER 5/16” HOLE Figure1BackofHeatbox 13. Tighten securing screw on bottom of face by thermostat or hole location. 14. Wiring A. Connect new Reset wires to lead wires previously cut, using wire connectors. B. Fasten wiring with wire ties so all wires fit neatly to the side of the motor and are out of the way. Cut off wire tie ends. C. Reconnect supply lead wires to heater securely, using wire connectors. Double check connections for tightness. 15. Reinstall heater into wall can tabs first, then attach screw. 16. Attach grill. 17. Turn power on and test heater. Point 2 Point 1 Point 3 CONTACT POINT TABS RESET TABS Figure 2 Back of Heatbox Face Cover TWISTTWISTFigure3 Warranty LIMITED 90 DAY WARRANTY: Cadet will repair or replace any Cadet part found to be defective within 90 days from the date of purchase. This warranty only applies to parts purchased or installed after the expiration of any other applicable warranty period. These warranties do not apply: 1. Damage occurs to the product through improper installation or incorrect supply voltage; 2. Damage occurs to the product through improper maintenance, misuse, abuse, accident, or alteration; 3. The product is serviced by anyone other than Cadet; 4. Refurbished products; 5. If the date of manufacture of the product cannot be determined; 6. If the product is damaged during shipping through no fault of Cadet. 7. CADET’S WARRANTY IS LIMITED TO REPAIR OR REPLACEMENT AS SET OUT HERE...

Este manual também é adequado para os modelos :
Eléctrico - C072 (147.71 kb)
Eléctrico - C151 (147.71 kb)
Eléctrico - C202 (147.71 kb)
Eléctrico - C208 (147.71 kb)

Escreva a sua própria avaliação do dispositivo



Mensagem
Seu nome :
Introduza os dois dígitos :
capcha





categorias