Assessments - 2, GPA: 4
(
)
)
|
Facilidade de uso
Turn Thermostat 2. It is recommended that you store the unit in its setting. like a bed, where openings may become blocked. sides and rear. Control fully clockwise to highest position Figure 1 CONTROL PANEL CLOSE-UP 15. To disconnect heater, turn controls to OFF, then original carton. Please DO NOT attempt to open or repair the 4. DO NOT run cord under carpeting. DO NOT cover ( Largest ). Select Mode to begin operation. remove plug from outlet. DE CG F A B heater. cord with throw rugs, runners, or the like. Arrange 4. Avoid overloading your circuit by not using other high 16. Avoid the use of an extension cord because the AUTO SAFETY SHUT-OFF cord away from traffic area and where it will not be wattage appliances in the same outlet. At 1500 extension cord may overheat and cause a risk of fire. tripped over. Watts, this unit draws 12.5 Amps. This heater is equipped with a patented, technologically However, if you have to use an extension cord, the If you have any questions regarding your product or 5. This heater is not intended for use in bathrooms, advanced, safety system that requires the user to reset cord shall be No. 14 AWG minimum size and rated Mode Control would like to learn more about other SunbeamTM laundry areas and similar indoor location. NEVER the heater if there is a potential overheat situation. When not less than 1875 watts. Turn the Mode Control to the desired setting: products, please contact our Consumer Service locate heater where it may fall into a bathtub or a potential overheat temperature is reached, the system 17. If the heater will not operate, see specific instructions Department at 1-888-264-9669 or visit our website at other water container. I/O - Off Mode will automatically shut the heater off. It can only resume on Auto Safety Shut-off. 6. Extreme caution is necessary when any heater is operation when the user resets the unit. 18. DO NOT attempt to repair or adjust any electrical or If you want to shut off the heater at any time during used by, or near children or invalids, and whenever mechanical functions on this unit. Doing so will void operation, turn the Mode Control to Off ( I/O ) position. To Reset the Heater: the heater is left operating and unattended. your warranty. The inside of the unit contains no user Power Light Ring will remain lit until the heater is turned 1. Turn the Mode Control to the Off ( I/O ) position. 7. Always unplug the heater when not in use. serviceable parts. All servicing should be performed to Off ( I/O ). 2. Unplug the heater and wait 30 minutes for the unit 8. When unplugging, be sure to pull by the plug and by qualified personnel only. to cool down. not the cord. -Fan only Setting 19. Discontinue use if plug or outlet is hot. It is A I/O = Off 3. After the 30 minutes, plug the unit in again and 9. DO NOT insert or allow foreign objects to enter any recommended that the outlet be replaced if plug or Heater will run at fan-only operation without heat output. = Fan Setting operate normally. ventilation or exhaust opening as this may cause an B outlet is hot to touch. electric shock or fire, or damage the heater. 1 - Low Heat C 1 = Low Heat 4. Place heater on firm level surface. 10. DO NOT operate heater with a damaged cord or plug, D 2 = High Heat The heater will run continuously at 1000W. or after the heater malfunctions, has been dropped PLEASE READ AND SAVE E Mode Control or damaged in any manner. Return appliance to 2 - High Heat F Power Light Ring (It only lights up manufacturer for examination, electrical or THESE IMPORTANT The heater will run continuously at 1500W. when unit is on.) mechanical adjustment, or repair. SAFETY INSTRUCTIONS NOTE: To start heater or fan only operation, make sure G Thermostat Control the Thermostat Control is turned fully clockwise to the highest position ( Largest ). THIS APPLIANCE HAS A POLARIZED PLUG (one blade is wider than the Thermostat Control other). To reduce the risk of electric shock, this plug is intended to fit in a polarized outlet only one way. If the plug does not fit fully in the outlet,1. Before setting the thermostat, allow heater to operate reverse the plug. If it still does not fit, contact a qualified electrician toand warm up the room. As noted before, you need to install the proper outlet. turn the Thermostat Control to High ( Largest ) to start the heater. DO NOT ATTEMPT TO MODIFY THIS PLUG OR DEFEAT THIS 2. When the desired temperature comfort level is SAFETY FEATURE IN ANY WAY. reached, lower the thermostat setting until the VEUILLEZ LIRE ET CONSERVER CES DIRECTIVES DE SECURITE IMPORTANTES CARACTERISTIQUES – UTILISATION NETTOYAGE/ENTRETIENDEP ANNAGE Lors de l’utilisation d’un appareil electrique, il faut causer des chocs electriques ou un incendie, et meme 18. NE tentez PAS de rep...
Este manual também é adequado para os modelos :Eléctrico - SCH160-CN (602.32 kb)