Assessments - 3, GPA: 3.7
(
)
)
|
Facilidade de uso
Low High Flashing Bar Normal Set the Comfort at the mid point (5 bar) by pressing the + or -buttons to change the number of illuminated bars. Low High Normal If the morning room temperature is not at the desired level, then adjust the Background heat level by pressing and holding down the + button on the temperature control display until 10 red lights are illuminated, continue to hold the +button for a further 7 seconds and a single red light will flash. Use the + button to increase room temperature and the flashing red light will move to the right. Use the -button to decrease room temperature and the flashing red light will move to the left. Flashing Bar After 20 seconds the temperature control will display will return to the Comfort Heat control mode. It may require a few days fine-tuning to achieve an optimum comfort level. On subsequent days increase or decrease the temperature by one red light until a satisfactory comfort level has been established. Once established the radiator will automatically adjust to suit seasonal changes in temperature. During mild weather background heat may not operate as Comfort Heat will be sufficient. Everyday Operation Once the Background level has been set (see Achieving Optimum Comfort Level above), this should not require any further adjustment. Adjust the Comfort setting as required to suit your comfort needs and occupancy pattern. For a short period of non occupancy the control can be lowered slightly (we recommend by no more than 2 bars) to save energy when the room is unoccupied and increased again when more heat is needed. Non Occupancy (vacant) For long periods of non occupancy, reduce the Background and the Comfort to their lowest settings. It will take 24 hours for room temperature to reach a comfortable level when resetting from Low settings to Normal settings. Child Lock Operation To activate the child lock simultaneously depress the + and buttons for a period of 3 seconds. After this period the child lock is in operation and the LED will illuminate for short period and then revert to the setback setting. The LED beside the key symbol will illuminate while the child lock is in operation. Once in the locked position, if either of the controls are operated the LED will resume maximum illumination for a short period before reverting back to the setback position. To deactivate the child lock, depress the buttons simultaneously again for 3 seconds and the buttons will become active. Safety - Overheat Protection For your safety, this appliance is fitted with thermal cut-outs. In the event that the product overheats, the cut-outs switch the radiator off automatically. In the event of these safety cut-outs activating please inform the installer or Dimplex Customer Services for advice in order to reset the cut-outs. Two Zone Wall Mounted Programmer (only applicable if Programmer is fitted to DuoHeat installation) RX010006 - Pilot Wire, or RX010007 - Mains Borne Signalling The programmer has two modes (i) AUTO or (ii) MANUAL (i) In “Auto” mode, the radiator will change between Comfort and Setback modes (as shown in the table below) depending on your seven day programme. To change the programme settings or temporarily over ride the programme, see the appropriate programmer instructions. (ii) “Manual” mode will override the auto programme setting. There are four “Manual” mode settings shown in the table below. Programmer Mode Temperature Setting DuoHeat Radiator – “Temperature control display setting” Comfort Comfort Setting (radiator setting). Each Radiator will operate as set in “controls” section of Operating Instructions. Display will remain as shown in Quick Start Guide H Setback Setback will reduce the Comfort setting by 2°C, and will leave the Background unaffected. Display will show two red bars less.eg. if “Comfort” displays 5, “Setback” will display 3 red bars. JFrost Protect Room temperature will be maintained at 16°C with Background operating. Display will show one red bar. Off This will completely switch off radiators, e.g. during the summer heating may not be required. Display will show one red bar. Note: It will take 24 hours for room temperature to reach a comfortable level when resetting from “Setback”, “Frost Protect”, “Off” to “Comfort”. Cleaning To maintain the external appearance of the radiator it need only be wiped over occasionally with a dry duster. During the summer months, or at other times when the appliance is not is use and is completely cold, the opportunity should be taken to wipe over with a damp cloth. Do not use abrasive cleaning powders or furniture polish. Discoloration of wall finishes can sometimes occur immediately above a radiator due to the properties of some paints and decorating materials or the presence of environmental impurities in the air (such as soot or incense generated from the burning of candles etc.). After Sales Service Your Dimplex DuoHeat radiator is guaranteed for two years from date of purchase. We undertake to e...
Este manual também é adequado para os modelos :Eléctrico - Duo300i (122.35 kb)