Log:
Assessments - 2, GPA: 4.5 ( )

Instruções de Operação United States Stove, Modelo AIR

Fabricante : United States Stove
Arquivo Tamanho: 138.13 kb
Arquivo Nome :
Língua de Ensino: en
Ir para baixar



Facilidade de uso


This will allow for more complete combustion and less buildup of tars or soot in the chimney. 1. Set thermostat to HIGH before opening feed door. 2. Wood Fire-Model 1303- Add wood to a convenient level. WARNING! NEVER STORE FLAMMABLE LIQUIDS, ESPECIALLY GASOLINE, IN THE VICINITY OF THE FURNACE. ADJUSTING BLOWER LIMIT CONTROL SETTINGS The temperature in the plenum of the warm air furnace at which the blower turns on or turns off, is controlled by the setting of the pointers in the blower limit control. (See Fig. 12) These pointers may be adjusted to achieve the desired warm air output from the furnace. (See Fig. 12 Below) 1. Moving both pointers toward the right (counter clockwise)- this increases the temperature setting at which the blower will turn on and off. 2. Moving both pointers toward the left (clockwise)- this decreases the temperature setting at which the blower will turn on and off. 3. Moving the pointers away from each other will increase the time that the blower will run on each warm air cycle. BLOWER FAN "OFF" POINTER BLOWER FAN "ON" POINTER BLOWER LIMIT POINTER & STOP Fig. 12 CAUTION! DO NOT OPERATE WITH THE FEED AND/ OR ASH DOOR OPEN. THIS FURNACE IS DESIGNED FOR THERMOSTATIC OPERATION. OPERATION WITH ANY OF THESE DOORS OPEN WILL OVERHEAT AND DAMAGE THE FURNACE. CAUTION! NEVER USE GASOLINE, GASOLINE-TYPE LANTERN FUEL, KEROSENE, CHARCOAL LIGHTER FLUID, OR FLAMMABLE LIQUIDS TO START OR "FRESHEN UP" A FIRE IN THE FURNACE. 17 Service Hints Do not expect a furnace to draw. It is the chimney that creates the draft. Smoke spillage into the house or excessive buildup of water or creosote in the chimney are warnings that the chimney is not functioning properly. Correct the problem before using furnace. Possible causes are: 1. The connector pipe may be pushed into the chimney too far, stopping the draft (Fig. 6) 2. Do not connect two furnaces or a stove and furnace into the same chimney flue. 3. The chimney used for a furnace must not be used to ventilate the cellar or basement. If there is a cleanout opening at the base of the chimney, it must be closed tightly. 4. If the chimney is operating too cool, water will condense in the chimney and run back into the furnace. Creosote formation will be rapid and may block the chimney. Operate the furnace at a high enough fire to keep the chimney warm, preventing this condensation. 5. If the fire burns well, but sometimes smokes or burns slowly, it may be caused by the chimney top being lower than another part of the house or a nearby tree. The wind blowing over a house or a tree, falls on top of the chimney like water over a dam, beating down the smoke. The top of the chimney should be at least 3 feet above the roof and be at least 2 feet higher than any point of the roof within 10 feet (Fig. 5). 6. See page 19 for list of trouble shooting tips. A draft reading of .05 to .06 w.c. is suggested for proper burning of this unit when using wood. Chimney Maintenance Creosote and Soot - Formation and Need for Removal When wood is burned slowly, it produces tar and other organic vapors, which combine with expelled moisture to form creosote. The creosote vapors condense in the relatively cool chimney flue of a slow-burning fire. As a result, creosote residue accumulates on the flue lining. When ignited, this creosote makes an extremely hot fire. When coal is burned, the products of combustion combine with moisture to form a soot residue which accumulates on the flue lining. When ignited, this soot makes an extremely hot fire. The chimney should be inspected at least twice monthly during the heating season to determine if a creosote or soot build up has occurred. If creosote or soot has accumulated, it should be removed to reduce the risk of a chimney fire. Chimney fires burn very hot. If the chimney catches fire, immediately call the fire department, then reduce the fire by closing the inlet air control. Pour a large quantity of coarse salt, baking soda or cool ashes on top of the fire in the firebox. CAUTION A chimney fire may cause ignition of wall studs or rafters which you thought were a safe distance from the chimney. If you have a chimney fire, have your chimney inspected by a qualified person before using again. 18 Trouble Shooting Tips for Warm Air Furnace LIST OF PROBLEMS POSSIBLE CAUSE SOLUTIONS 1. Smoking when feed door is open. a) Insufficient Draft. b) Clogged chimney or chimney connector. c) Down draft in chimney a) Set thermostat higher. b) Clean chimney. c) Add raincap to chimney. 2. Furnace does not heat. a) Wood not seasoned and dry. b) Blower control set too low. c) Insufficient flue draft. a) Allow wood to season in a dry, well ventilated area for 6 mo. b) Set blower control to higher temperatures. c) Set flue draft. (See page 9) 3. Blower does not run. a) Improperly wired. b) Bad blower control. c) Bad relay. d) Bad blower motor. a) Wire unit properly. b) Replace blower control. c) Replace relay. d) Replace blower. 4. No air from registersfan runni...

Este manual também é adequado para os modelos :
Eléctrico - 1303 (138.13 kb)

Escreva a sua própria avaliação do dispositivo



Mensagem
Seu nome :
Introduza os dois dígitos :
capcha





categorias