Assessments - 4, GPA: 4 ( )

Fabricante : Desa Arquivo Tamanho: 2.84 mb Arquivo Nome : Língua de Ensino:

Tighten the piezo mounting nut. Do not over tighten the nut. 3. Connect the burner hoses together as shown in Figure 2. Wrench tighten to insure leak tight connection. 4. Mount the burner assembly onto the support arm using the burner head mounting brackets and brass screws as shown in Figure 3. Place side of bracket into the slot on support arm. Secure with screw. Make certain that the air holes on the sides of the burner tube are not blocked. Securely tighten the burners into place. 5. Attach the electrode wires to the piezo ignitor as shown in Figure 4. Safety Information Continued Piezo Ignitor Piezo Mounting Nut Burner Support Bracket Figure 1 - Installing Piezo Ignitor Figure 2 - Attaching Burner Hoses to Regulator Burner Head Assembly Support Arm Slot Air Hole Burner Head Mounting Bracket Brass Screw Figure 3 - Attaching Burner Head Assembly to Support Arm Piezo Ignitor Electrode Wires Figure 4 - Attaching Electrode Wires to Piezo Ignitor Operating Instructions 1. Check heater for damage. If heater is damaged, promptly inform dealer where you bought heater. 2. Follow all of the safety and operating precautions. 3. Check the "O" ring on the POL before each use. Replace the "O" ring if there is any sign of wear or damage. 4. Make sure heater regulator knob is in the "OFF" position. 5. 30,000 Btu Models Only Attach the heater to the guard on the propane/LP cylinder with the support arm on the inside of the guard and bolts through two holes in the guard (see Figure 5). Tighten the support arm bracket into place using the wing nuts provided. 6. For All Models Connect the POL fitting at regulator to the propane/LP cylinder by rotating the POL nut counter clockwise into the propane/LP cylinder's valve outlet and securely tighten with a wrench. WARNING: Attach heater in upright position. Never attach heater in a horizontal position. This could lead to dangerous flare-ups or fire. 7. Securely tighten all gas connections. 8. Open the cylinder's gas valve and check all connections for leaks. Apply mixture of liquid soap and water to gas joints. Bubbles forming show a leak that must be corrected. DO NOT USE A FLAME. To START Heater WARNING: When lighting the heater DO NOT look over top of heater (reflector). Stand to the side of the heater during ignition. Do not stand or have any part of your body in front of the heater. WARNING: MAKE SURE THERE IS NO OPEN FLAME IN THE AREA. Fully open the valve on the propane/LP cylinder. Read all lighting instructions before attempting to ignite heater. 1. Turn the heater regulator knob counterclockwise to the "HI" position. 2. Repeatedly push and release the piezo ignitor (dual burner), or place a lighted match near the face of the heating element (mesh screen) of the burner you are lighting, using the hole located on the side of the reflector. See Figure 6. CAUTION: Do not light at the orifice. 3. Depress the red button on the safety valve admitting gas to the burner (see Figure 6). WARNING: Do not depress red valve button before repeatedly activating the piezo or inserting match. Support Arm Support Arm Bracket Bolt Red Button on Safety Valve Regulator Figure 6 - Lighting Heater With a Match Figure 5 - Attaching Support Arm and Regulator to Propane/LP Tank 4. When the gas on the face of the mesh screen lights, continue to hold the valve button depressed for 30 seconds, then release. 5. If flame goes out, wait 5 minutes and repeat the lighting procedure. 6. If heater will not light after repeated tries, do not attempt to repair heater. Return heater to nearest authorized service center or to manufacturer of this product. 7. For dual burner models, repeat steps 1 through 4 to ignite the other burner. 8. After both burners or single burner, are lit, turn the heater regulator knob to the desired heat setting (LOW, MED, HI). to STOP Heater 1. Securely close valve on the propane/LP cylinder. 2. Turn the heater regulator knob to the "OFF" position. Wait 15 minutes for the heater to cool down before handling heater. 3. Always remove the heater from the propane/ LP tank after each use. Do not store the heater while attached to propane/LP tank. Remove the heater from the propane/LP tank by turning the fuel connector nut clockwise. Always store propane/LP tank outdoors. Never store propane/LP tank in an enclosed area. To RESTART Heater 1. Securely close valve at propane/LP cylinder. 2. Wait 5 minutes. 3. Restart following To Start Heater procedure, page 5. Maintenance and Storage 1. Inspect heater before each use. Check connections for leaks. Apply mixture of liquid soap and water to connections. Bubbles forming show a leak that must be corrected. Correct all leaks at once. Have heater inspected at least annually by a qualified service person. 2. Before each use, check the soft "O" ring seat at the bullnose of the POL fitting. If the "O" ring is cut, scuffed, or otherwise damaged, replace it with part number 6681. 3. Inspect hose/regulator assembly before each use. If hose is highly ...

Baixe o seu

Para fazer o download, introduza 2 dígitos :