Assessments - 3, GPA: 3.7
(
)
)
|
Facilidade de uso
Note: If the power supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid a hazard. 2 How to Use This appliance is intended for household use only. Important: For warranty verification, do not remove line cord sticker. The Advanced Safety Technology™ (AST) system features unique technology built into your heater that offers protection detailed in the "Special Features" section. Included in AST is a shock protection device built into the line cord and equipped with a test button to check operation: Before Use: 1. Press RESET button on line cord safety device (A). 2. Plug into a regular AC electrical outlet. 3. Press TEST button and RESET button will pop out (see A) to show safety device is operating properly. Repeat this procedure each time you use heater to confirm safety device is operational. Should RESET button not pop out, do not use heater. Call appropriate "800" number on the cover of this book. At any time, should this unit detect an electrical shock hazard, it will immediately shut off. To restore power, you must press RESET button on the line cord protection safety device to reactivate circuit. Important: During the first few minutes of initial use, you may notice a slight odor. This is normal and will quickly disappear. This heater is intended for use on a flat, stable surface, such as a floor, tabletop, shelf, or desk in a location where the airflow grille openings won’t be obstructed. Do not use in wet or moist locations, like bathrooms or laundry areas, or in areas where paint or other flammable or volatile liquids are used or stored. Caution: Be sure no other appliances are plugged into same circuit with heater/fan. A circuit overload could occur. 1. Place heater on a flat, stable surface, such as a floor or tabletop where airflow grille opening won’t be obstructed. Use fold-down handle when moving unit. Do not use in wet/moist locations, like bathrooms or laundry areas, or in areas where paint, flammable, or other volatile liquids are used or stored. 2. Be sure control knob is in the OFF position, then plug heater into a standard AC outlet. 3. Room Select™ Control: Turn switch to the appropriate setting for a small (approx. 10' x 10'/3 m x 3 m), medium (approx. 12'x12'/3.8 m x 3.8 m) or large (approx. 12'x 16'/3.8m x 5m) room (B). 4. Turn thermostat control to HOT to activate heater. Once desired room temperature is achieved, lower thermostat control toward FROST WATCH until unit cycles off. The thermostat will cycle unit on and off to maintain your comfortable temperature level. 5. Turn timer knob to the 1 hr., 2 hr., 3 hr. or 4 hr. setting to select how long you’d like heater to stay on. The unit will shut off automatically once the selected time runs out. To operate heater continuously, turn timer knob to ON. Remember to shut unit Off when done. 6. To use as a fan without heat, move control knob to FAN ONLY and thermostat control toward HOT until fan begins to operate. No heating will occur in this mode. 3 4 Product may vary slightly from what is illustrated. 1. Fold-down handle 2. Timer knob 3. Control knob 4. CAUTION indicator 5. Heat sensor patch 6. Front grille 7. Roll-over bars 8. Power indicator 9. Thermostat control RESET TEST To restore power, you MUST press the RESET button on the line cord protection safety device to reactivate the circuit. A B 220UHPub1000002304 5/6/05 11:17 AM Page 4 220UHPub1000002304 5/6/11:Page 6 7. To turn off, turn thermostat and control Note: The power indicator glow even if thermostat 8. Frost Watch: When heater is plugged can select any setting for thermostat control on toward Heater will remain off unless the temperature F/4°C). If this happens, FROST WATCH will automatically cycle unit pipes or frost damage. Special features and the Advanced Safety ™ (AST) system 1. This unit has a safety auto off, plus a safety If unit experiences excessive heat, the safety CAUTION light will go on. If this happens, turn immediately. Be sure front grille is not blocked and nothing is airflow. Unplug unit, let it cool down, and wait 10-15 minutes. reset, plug unit back in and turn thermostat control to HOT. You can then readjust temperature or room settings. If unit fails to operate after mean heater has internal damage and thermal fuse has been can no longer operate. 2. A built-in tip-over switch will cut power if the unit is accidentally knocked forward or backward. To reset, simply place heater in upright position on a level surface. If it falls forward, the roll-over bars on the front of unit will prevent heater from burning surfaces. 3. Even though unit has a cool-touch housing, the front grille will get hot. Be careful not to touch it during operation. Heat sensor patch on the front: This patch changes color when front grille becomes hot to the-touch (C). Do not touch front of heater when this happens. Care and Cleaning This heater is permanently lubricated and will not requi...