Assessments - 3, GPA: 3.7
(
)
)
|
Facilidade de uso
Return heater to authorized service facility for examination, electrical or mechanical adjustment, or repair. 7. This heater is not intended for use in bathrooms, laundry areas and similar indoor locations. NEVER locate heater where it may fall into a bathtub or other water container. To protect against electrical hazards, DO NOT immerse in water or other liquids. 8. DO NOT touch the control panel or plug with a wet hand. 9. DO NOT run cord under carpeting. DO NOT cover cord with throw rugs, runners, or similar coverings. Arrange cord away from traffic area and where it will not be tripped over. 10. DO NOT insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric shock or fire, or damage the heater. 11. To prevent a possible fire, DO NOT block the air intakes or exhaust in any manner. DO NOT use on soft surfaces, like a bed, where openings may become blocked. 12. A heater has hot and arcing or sparking parts inside. DO NOT use in areas where gasoline, paint, explosive and/or flammable liquids are used or stored. Keep unit away from heated surfaces and open flames. 13. Avoid the use of an extension cord because the extension cord may overheat and cause a risk of fire. However, if you have to use an extension cord, the cord shall be No. 16AWG minimum size and rated not less than 1875W. 2 14. To avoid fire or shock hazard, plug the unit directly into a 120 V AC electrical outlet. 15. To disconnect heater, turn controls to OFF, then remove plug from outlet. Pull firmly on the plug, DO NOT unplug by pulling on the cord. 16. Always unplug the unit before moving or cleaning, or whenever the heater is not in use. 17. Use only for intended household use as described in this manual. Any other use not recommended by the manufacturer may cause fire, electric shock, or injury to persons. The use of attachments not recommended or sold by unauthorized dealers may cause hazards. 18. Always use on a dry, level surface. Use on floor only. 19. WARNING: To reduce the risk of fire or electric shock, DO NOT use this unit with any solid-state speed control device. 20. DO NOT attempt to repair or adjust any electrical or mechanical functions on this unit. Doing so will void your warranty. The inside of the unit contains no user serviceable parts. Qualified personnel should perform all servicing only. 21. DO NOT use outdoors. 22. SAVE THESE INSTRUCTIONS. SPECIFICATIONS Voltage Rating 120 V (60Hz) Power Consumption 750W / 1500W AMPS 7.5A / 12.5A Unit Size 6.9 in. (W) x 6.9 in. (D) x 18.8 in. (H) Unit Weight 4.53 lbs, 3 PRODUCT DIAGRAM Power Indication Light Oscillation Ceramic Heating Element & Grill Power Select Tip Over Safety Switch 4 OPERATING INSTRUCTIONS Place the heater on a firm, level surface and plug into a grounded 120 V 60Hz power outlet. Only operate the heater when it is in the upright position. Use the instructions below to operate the heater using the control panel. 1. Turn on the POWER SELECT dial to the desired power setting (High/Low/Fan). When this switch is turned to the desired setting, the red POWER INDICATION LIGHT will light up indicating there is power to the unit. 2. This heater is able to run in LOW, HIGH, and Fan only mode. Choose the desired mode based on your comfort level. 3. To activate oscillation, turn the OSCILLATION dial to SWING. Once it is located, the heater will rotate side-to-side spreading warm air throughout the room. SAFETY FEATURES Polarized Plug Warning: This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of electric shock, this plug is intended to fit into a polarized outlet only one way. If the plug does not fit fully into the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not attempt to modify the plug in any way. DO NOT DEFEAT THE SAFETY PURPOSE OF THE POLARIZED PLUG. Tip-Over Safety Switch This heater equipped with tip-over safety switch located underneath the base of the heater (SEE ILLUSTRATION ON PAGE 4). This switch must be pressed inward for the heater to function properly. Some soft surfaces such as carpet may not be able to fully press in this switch. For some soft surfaces, a hard flat object will need to be placed underneath the heater for it to function properly. PLEASE DO NOT TAPE OR GLUE THIS SWITCH. 5 MAINTENANCE WARNING: ALWAYS UNPLUG THE CORD BEFORE MOVING OR SERVICING. CLEANING: IMPORTANT! DO NOT IMMERSE HEATER IN WATER! Clean the heater grills using the vacuum brush attachment on your vacuum cleaner. This will remove lint and dirt from the inside of the heater. DO NOT ATTEMPT TO TAKE HEATER APART. Clean the body of heater with a soft cloth. CAUTION: Do not use gasoline, benzine, thinner, harsh cleaners, etc. as they will damage the heater. NEVER USE ALCOHOL OR SOLVENTS. SAFETY FEATURES 1. A thermal overload protector is built in to prevent overheating. 2. When an overheat temperature is...