Assessments - 4, GPA: 3.5
(
)
)
|
Facilidade de uso
Convenient 8hr auto-off timer 7. 2 heat setting, plus auto mode and fan only setting 8. 90° degree oscillation for warmth throughout the room 9. On/Off button and variable temperature dial, to turn the heater on and off and to maintain your desired temperature setting 10. Power-On indicator Not Shown • Convenient carry handle • Safety tip-over cut-out switch KCE440_IB_FA.indd 6 12/10/09 2:26 PM Quick Start Guide The heater will start operating at the HIGH heat setting. Leave at HIGH until the room temperature is comfortable. Turning the heater on Setting the heating mode Setting thevariable temperature Setting the oscillation Turning the heater off Press the MODE button to select AUTO setting. Plug the cord into a 230V or 240V power point and switch on. Rotate the dial clockwise to increase temperature, and anti- clockwise to decrease temperature. Switch on the unit using the ON/OFF switch. Press the SWING button to activate. Press again to stop the oscillation. Press the On/ Off button to activate. Press the On/Off button to place the heater in standby mode. Switch off the unit using the ON/OFF switch. Press the MODE button to select the LOW heat setting, and retain a comfortable temperature for your room. TEMPERATURE SWING Hints/Tips to Retain Heat in Your Home • Don’t overheat your home. The temperature of a heated room in winter should be 18-21°C • Your heater will work more efficiently if you stick to Kambrook’s recommended clearance spaces • Choose the right size heater for the room type you want to heat • Zone off unoccupied rooms by closing doors and only heat the main living areas • Fit window coverings like curtains to limit winter heat loss • Put draft stoppers, such as a rolled up towel, at the bottom of outside doorways to keep out cold air • Keep the heat in and the cold out by installing wall and ceiling insulation. • Avoid placing items too close to the heater (both at the front and back) for optimal air flow 7 KCE440_IB_FA.indd 7 12/10/09 2:26 PM 8 Using Your Ceramic Tower Heater Setting the Heating Mode To activate the heater, press the On/ Off button. The heater will start operating on the HIGH heat setting (1800 watts) and the LCD screen will illuminate, displaying the ambient room temperature and heat setting. NOTE: After several seconds, the LCD screen will fade, but the heater settings will remain visible. Use the MODE MODE button to select the desired heat setting. The mode button allows you to scroll through the various heating modes. HIGH – High heat setting (1800 watts) LOW – Low heat setting (900 watts) AUTO – for use with the electronic thermostat FAN – for fan only operation To switch the heater into standby mode, press the On/Off button. Turn the heater off by switching the Power switch located on the right hand side of the base, to the off position. Remove any promotional material or packaging from the heater. Unwind the cord to its full length and place the heater on a firm, level surface in a stable upright position. Visually inspect the air inlet and outlets to ensure there are no blockages. When unpacking the heater, check to see you have received the remote control, before discarding the packaging. Turning Your Heater On Plug the cord into a 230V or 240V power point and switch on. NOTE: To avoid an electrical circuit overload, it is recommended that no other appliances are plugged into the same circuit as your heater, when it is in use. Turn the heater on by switching the Power switch located on the right hand side of the base, to the on position. An audible beep will sound, and the red power indicator light will illuminate. The heater is now in standby mode. Using the Remote Control Your heater may be operated using either the control panel or the remote control. The remote control uses 2 x AAA batteries. To access the battery compartment, simply remove the cover at the rear of the remote control. To operate, ensure that you point the remote control at the heater. An audible beep will sound with the press of each button. KCE440_IB_FA.indd 8 12/10/09 2:26 PM To activate the heater, press the On/ Off button. The heater will start operating on the HIGH heat setting (1800 watts) and the LCD screen will illuminate, displaying the ambient room temperature and heat setting. NOTE: After several seconds, the LCD screen will fade, but the heater settings will remain visible. Use the MODE MODE button to select the desired heat setting. The mode button allows you to scroll through the various heating modes. HIGH – High heat setting (1800 watts) LOW – Low heat setting (900 watts) AUTO – for use with the electronic thermostat FAN – for fan only operation To switch the heater into standby mode, press the On/Off button. Turn the heater off by switching the Power switch located on the right hand side of the base, to the off position. Remove any promotional material or packaging from the heater. Unwind the cord to its full length and place the heater on a firm, level surface in a stable ...