Assessments - 4, GPA: 4
(
)
)
|
Facilidade de uso
To set the required power level, proceed as follows: press the “power setting” button one or more times within 5 seconds to select the power level, as per the following sequence: The power selecting can be circulated and the red power pilot light will be on during the heater powered on. To cancel the manual mode, push the button “power setting” until the LCD appear “OFF”, the red power pilot light will be extinguished. Now the unit can be set in auto mode. 3.) SETTING THE AMBIENT TEMPERATURE Adjust the “+” or “-“ button to the desired ambient temperature from 5 to 35.C at any time during operation. By pushing once the “+” or “-“ button the temperature (shown on the right side of the display) will increase or decrease by 1.C. Keep the button pressed to move through the temperature in fast mode. This heater has a sensitive temperature detector, which automatically monitors the current ambient temperature and switches the unit on to maintain your chosen temperature. If the selected temperature is higher than the actual room temperature, the appliance will start automatically and rapidly heat the room until it reaches the selected temperature. The unit will automatically maintain the temperature at a constant level. 4.) USING OF TIMER The function of the time works only under the setting manual mode setting. After the unit is powered on in the manual mode, press the button “timing” one or more times within 5 seconds to select the timing level, as per the following sequence: 0:00h – 0:30h – 0:45h – 1:00h – 2:00h – 4:00h – 8:00h The timing setting can be circulated as above sequence and the timing pilot lamp light will be on during the timing function activation. To cancel the timing, push the button “timing” until the LCD appears “0:00h” or push the button “power setting” until the LCD appears “OFF” and wait for 5 seconds, the yellow timing pilot light will go out. MAX AM C Time Set Temperature MAX AM 8:00 35 C Set Temperature Time OFF MAX AM AM MAX C C MEDIUM POWER MAXIMUM POWER MAX AM MAX AM 35 35 C C OFF OFF MINIMUM POWER 5.) ANTI-FREEZE SETTING Press the “power setting” button and it is recommended to select the maximum power level. Set the temperature to 5.C with the “-“ button. When set this way, the appliance will switch on automatically only if the room temperature falls below 5.C, to prevent freezing at minimum energy consumption. 6.) USING OF BOOKING TIMER NOTE: If you want to operate the appliance in the auto mode, press the button “booking timer” to activate it. I In this mode, the function of the timing will be i invalidated. Press the button “booking timer” one or more times within 5 seconds to select the booking timing mode, as per the following sequence: The booking timing mode setting can be circulated as above sequence and the yellow timing pilot light will be on during the heater operating in auto mode. a. Auto on When the LCD shows “AUTO ON”, the unit comes into auto power on timing state. To select what time you require the heater to be on, push the button “hour” and “minute” until your required operating time appears. b. Auto off When the LCD shows “AUTO OFF”, the unit comes into auto power off timing state. To select what time you require the heater to be off, push the button “hour” and “minute” until your required operating time appears. The operating time has a span of 24 hours. Auto on and auto off default value is ”00:00”. c. Auto Press the button “booking time” until the LCD appears “AUTO”. This indicates that the auto mode comes into effect. The yellow timing pilot light now lights up. During operating in the auto mode, you can use the “+” button or “-” to set the desired comfort temperature as described above and the appliance will automatically switch on or off at the preset time and automatically maintain the preset comfort temperature. NOTE: Do not press the button “power setting” when operating in the auto mode, this will cancel the function of “booking timer”. To cancel the function of “booking timer”, press the button “booking timer” until blank appears and wait for 5 seconds or press the button “power setting”, the yellow timing pilot light will go out. NOTE: To keep the heater’s memory programmed, always leave the heater plugged in at the mains socket. If the heater looses its electricity supply, e.g. switched off at the mains socket or in the event of a power failure, the heater’s programs will be lost, and the heater will not work until reset. This heater includes an overheat protection system that shuts off the heater when parts of the heater are getting excessively hot. Once it occurs, the heater’s programs will be lost. To completely shut the heater off, turn the controls and power to OFF, and remove plug from the socket-outlet. MAX AM AUTO ON MAX PM AUTO ON C C OFF OFF AUTO OFF AUTO ON AM MAX AM AUTO MAX C C OFF OFF BLANK AUTO 27 Nourse Avenue Epping 2 Cape Town P.O. Box 975 Eppindust 7475 South Africa Tel: +27 21 534 8114 Fax: +27 21 534 8086 Service Centre Share Call...