Assessments - 4, GPA: 3.5
(
)
)
|
Facilidade de uso
DO NOT lubricate the Rubber Washer. J K Fishfi nder 80 2. Route the cable towards the back and slide the transducer into the mounting bracket. 3. Place a 5 mm Flat Washer on the 10-32 x Please read through these instructions thoroughly before attempting installation. Make sure 1.75" screw and insert the screw through you completely understand these instructions before you begin. When in doubt, seek profes the Mounting Bracket, Spacer and Rubber Washer. sional assistance. Be sure the wiring harness will reach the unit and transducer location before 4. Place the remaining 5 mm Flat Washer on the exposed end and install the 10-32 beginning installation. The Garmin Fishfinder 80 hardware allows for installation on either the transom or trolling motor. Please check the packing list below. If you are missing any items, S Lock Nut finger tight. The transducer will be please contact your Garmin dealer. tightened further after installation on boat. Packing List: J - 5 x 30 mm Screws (2) A - Fishfinder 80 Sonar Unit (1) K - 10-32 Lock Nut (1) B - Swivel Mount Bracket (1) L - 4 x 12 mm Screws (4) C - Swivel Base (1) M - 10-32 x 1.75 Screw (1) D - Mounting Knobs- Short (1), Long (1) N - 1/4” Cable Clamps (2) E - Mounting Knob Spacer (1) O - Plastic Spacer (1) F - Transducer With Power Cable (1) P - 1/4” Rubber Washer (1) G - Transducer Mount (1) Q - Cable Tie, 5.6” (4) (Cable not shown) H - Trolling Motor Mount Gasket (1) R - Cable Tie, 20” (1) I - 5 mm Flat Washers (2) S - Snap-Ring (1) Mounting the Transducer On a Trolling Motor 1. Slide the large Cable Tie through slot on the Transducer Mount with the ridges of the band facing up until equal lengths extend on both sides of the mount. (Note: For cold water or heavy timber/debris areas, a metal 4-5” worm gear clamp is recommended.) 2. Position the Mount Gasket on the curved top of the Mount. 3. Place the transducer assembly against the motor body of the trolling motor with the front of the transducer pointed away from the trolling motor propeller. 4. Place the pointed end of Cable Tie through the fastener hole on the opposite end and pull through (you will hear clicks) until snug. 5. Position the trans duc er so that is will be parallel with the bottom when in use and make sure the Gasket is aligned properly. Pull the Cable Tie end until tight. Excess may be trimmed off if needed. Tighten the 10-32 locking nut until it touches the mounting bracket and then tighten 1/4 turn more (do not overtighten). 6. Route the 30’ (9 m) transducer cable using the supplied cable ties to secure the cable to the motor shaft. If desired, the forward-facing portion (except the Cable Tie pocket) of the Transducer Mount may be filled with sealant to avoid debris accumulation. Selecting a Transom Mount Location For your sonar to operate properly, the transducer has to be located in clean (nonturbulent) water. The transducer should be mounted as near the center of the boat as possible. DO NOT cut the transducer lead, this will void your warranty and may cause the unit to not operate at optimal levels. DO NOT mount the transducer behind strakes, rivet lines, struts, fi ttings, water intake, discharge ports, eroding paint, or anything that creates air bubbles or causes the water to become turbulent. It is important that the transducer be as close to the center line as possible in calm, non turbulent water for optimal performance. Avoid mounting the transducer in locations where the boat may be supported during launching, hauling, trailering or storage. Mount the transducer away from the path of the prop on single drive boats. On twin drive boats, mount the transducer between the drives if possible. Do not mount the transducer directly in the path of the prop. The transducer can cause cavitation that may degrade the boat’s performance and damage the prop. Make sure the transducer is below water level when the boat is on plane at high speed. Mount the transducer parallel with the water line. Do not mount the transducer behind strakes, rivet lines, struts, fittings, water intakes or discharge ports. Mounting the Transducer On a Transom Drill Pilot Holes Here Tool List (not included) - Drill, 3/8" Wrench or Socket, 5/32" and 1/8" Drill Bits, Masking Tape, #2 Phillips Screw Driver, Marine Sealant 1. Position the transom mount at the selected location, making sure the transducer is parallel with the water line. Mark the center locations of each hole on the transom mount. (see figures to the right) 2. Using the 5/32" bit, drill the pilot holes approximately 1" (25 mm) deep at the marked lo ca tions. To avoid drilling the holes too deep wrap a piece of tape around the bit 1" from the point of the bit. 3. Apply Marine Sealant to the 5 x 30 mm screws. Attach the transducer to the transom Apply marine sealant to all screw using the 5 x 30 mm screws. Adjust the transducer to extend beyond the bottom threads to prevent water from of the transom approximately 1/8" (3 mm) on fiberglass hulls or 3/8" (10 mm) ...
Este manual também é adequado para os modelos :Sounders - Fishfinder 80 (388.05 kb)