Assessments - 3, GPA: 3.7
(
)
)
|
Facilidade de uso
Please read these instructions before use of this product. Adult assembly is required. Tool needed for assembly: Phillips Screwdriver (not included). Requires four LR20 ("D") alkaline batteries (not included) for operation. WARNING To prevent serious injury or death from falls and being strangled in the restraint system: • Always use the restraint system. Never rely on the tray to restrain child. • Never use with an active child who may be able to climb out of the seat. • Not recommended for children who can sit up by themselves (6 months approximately, until 9 kg (20 lbs). • Never leave the child unattended. • It is dangerous to use this product on an elevated surface. Parts Oval End Seat Tube Pad 2 Toys (Toys may be different than shown.) Toy Bar 4 Links Round End Seat Tube Seat Back Wire Motor Housing Housing 2 Tray Links Tray Rod Seat Back 2 Legs Front Curved Base Seat Bottom 2 Feet Assembly Tool (This tool is not a toy. Please throw away after assembly is complete.) Back Base IMPORTANT! Please remove all parts from the package and identify them before assembly. Some parts may be packed in the pad. Lock Nut – 23.8 cm Pin Screw – 2 #8 x 1.9 cm Screw – 3 #6 x 3.18 cm Screw – 2 All Shown Actual Size Note: Tighten or loosen all screws with a Phillips screwdriver. Do not over-tighten. 2 IMPORTANT! Before assembly, inspect this product for damaged hardware, loose joints, missing parts or sharp edges. DO NOT use if any parts are missing or broken. Contact Mattel for replacement parts and instructions if needed. Never substitute parts. 3 1 Button Leg Housing • Place a housing on a flat surface. • Insert the button end of a leg into the hole in the housing. • Push the leg in until it “snaps” into the housing. • Repeat this procedure to assemble the other leg to the other housing. • Pull the legs to be sure they are secure in the housings. If you can remove them, you have not assembled them correctly. Please re-read and repeat this assembly step. • Pull the other leg back until it “snaps” into place in the housing. • Repeat this procedure to “snap” the leg in the other housing into place. • Place the front curved base on a flat surface so that it curves away from you. • Place the back base on a flat surface, behind the front curved base. • Position the leg assemblies so that the hubs are facing each other. • Fit the ends of the legs over the ends of the front and back bases, as shown. Hint: You may need the help of another adult to help you balance the assembly. 2 Front Curved Base Hubs Back Base Assembly Leg CAUTION This package contains small parts in its unassembled state. Adult assembly is required. IMPORTANT! Before assembly, inspect this product for damaged hardware, loose joints, missing parts or sharp edges. DO NOT use if any parts are missing or broken. Contact Mattel for replacement parts and instructions if needed. Never substitute parts. 3 1 Button Leg Housing • Place a housing on a flat surface. • Insert the button end of a leg into the hole in the housing. • Push the leg in until it “snaps” into the housing. • Repeat this procedure to assemble the other leg to the other housing. • Pull the legs to be sure they are secure in the housings. If you can remove them, you have not assembled them correctly. Please re-read and repeat this assembly step. • Pull the other leg back until it “snaps” into place in the housing. • Repeat this procedure to “snap” the leg in the other housing into place. • Place the front curved base on a flat surface so that it curves away from you. • Place the back base on a flat surface, behind the front curved base. • Position the leg assemblies so that the hubs are facing each other. • Fit the ends of the legs over the ends of the front and back bases, as shown. Hint: You may need the help of another adult to help you balance the assembly. 2 Front Curved Base Hubs Back Base Assembly Leg CAUTION This package contains small parts in its unassembled state. Adult assembly is required. 4 3 HUBS FACING OUT FRONT BASE CURVES INWARD HUBS FACING IN • Check to be sure you have assembled the leg assemblies to the bases correctly. Please refer to the illustrations above. • If the leg assemblies are assembled incorrectly to the bases, simply pull the legs from the bases. Please re-read and repeat assembly step 2. • Set the frame assembly aside. CORRECT INCORRECT FRONT BASE CURVES OUT Assembly 4 3 HUBS FACING OUT FRONT BASE CURVES INWARD HUBS FACING IN • Check to be sure you have assembled the leg assemblies to the bases correctly. Please refer to the illustrations above. • If the leg assemblies are assembled incorrectly to the bases, simply pull the legs from the bases. Please re-read and repeat assembly step 2. • Set the frame assembly aside. CORRECT INCORRECT FRONT BASE CURVES OUT Assembly 55 4 • Align the hole in the seat tube with the hole in the armrest. • Insert a 3.8 cm pin screw through the armrest and into the seat tube. Tighten the screw. 5 Seat Bottom Round En...