Assessments - 3, GPA: 4
(
)
)
|
Facilidade de uso
To assure future protection, offered by Victor’s Extended Guarantee Protection Program. This operating manual describes the features and operation of the Victor 1460-4 electronic calculator. This calculator features the four basic arithmetic operations, two independent tax keys, percentage and percentage-ofchange, change sign, sigma, item count, non-add/date functions, backspace, and cost, sell, margin keys. Table of Contents General Maintenance Replacing the Ribbon Paper Feed Keyboard Diagrams Key Features Application Examples Warranty Extended Warranty Preparation BEFORE USING THE PRINTER FOR THE FIRST TIME: Remove the tape holding the ink ribbon in place. Before Beginning Calculation 1. Plug in AC power 2. Be sure that the paper roll and ribbon have bee installed properly. 3. Turn power switch on, and make sure that the display lights. A “C” will automatically be printed on the paper tape. 4. Set decimal point selector switch at the desired position. NOTE: Please remove the piece of tape holding the printer ribbon in place for transportation. General Maintenance 1. Do not place the calculator in hot, dusty, or damp locations. 2. To clean the housing, use a silicon-treated cloth. Do not use water or detergents. 3. Do not place anything on the housing, particularly on the head of the printer mechanism. 4. Turn off the power switch before removing the plug from AC wall outlet. 5. Turn the power switch off while not in use. How to Feed the Paper Tape 1. Plug in the calculator and turn it on. 2. Cut or tear evenly the end of the paper roll to get a straight edge. 3. Place the paper holder into position. (Fig. 4. Install the paper roll on the paper holder. 5. Insert the paper end into the printer slot. (Fig. 6. Press the Paper Feed (^) key to feed the paper to an adequate length. Replacing the Ribbon Your calculator is shipped with a 2-color ribbon already in place. You do not need to install or change it before you begin using the calculator. When you have been using your calculator for some time, however, the print will gradually become faint, indicating that you should change the ribbon. To change the ribbon, follow these steps. 1. Remove the paper roll, tearing the paper at the rear of the calculator. Use the Paper Advance (^) key to feed the remaining paper tape through the printer. Then remove the printer cover. 2. Remove the old ribbon by pulling it upward. 3. Install the ribbon spool with the black edge up. Roll from the outside of the full spool and place the first spool on the spindle not engaged by the lever. Thread the new ribbon along the outside of the guides and in front of the print wheels. Switch the lever to the other side and replace the second spool. 4. Rotate the spools to take up any slack. Replace the printer cover and the paper tape. (Replace with the Victor #7010 Ink Ribbon) Keyboard Layout This section describes the mode switches, data entry keys, and operating keys provided on your calculator. The following terms are used in discussing your calculator’s operation: • The accumulator is the area of the calculator’s logic that stores a running total of the results of addition and subtraction operations. It is the “adding machine” portion of the calculator. • The calculating register is the area of the calculator’s logic where the intermediate and final results of multiplication, division, and percentage calculations are stored. The contents of the calculating register do not affect the accumulator. • The keyboard register is the area of the calculator’s logic that stores the value that will immediately be used in the next calculation. • The item count register is the area of the calculator’s logic that counts your entries into the accumulator. Each positive or negative entry is counted as one item. • The memory register is the area of the calculator’s logic that accumulates amounts you add or subtract from the memory. Because the memory register is independent of the accumulator and the calculating register, it retains its value until you clear it with the Memory Total (MT) key. KEY AND SLIDE SWITCH FEATURES This section illustrates and describes the mode switches you can use to control your calculator’s operation. OFF ON · (OFF) The power is OFF. · (ON) The power is ON. P NP IP · (P) The printer is activated as long as the calculator is turned on. · (NP) The printer is activated only when the paper feed key or the non-add / date key is pressed. This is also called display only mode. · (IC) Activates the Item Count so that when the Total key is pressed, the Item Count will automatically print on the right hand side of the printed tape. ^ 5/4 Ў (^) This setting causes an answer to a calculation to automatically round up. (5/4) This setting causes automatic round off. If the last digit of the result that will be printed or printed / displayed upon rounding is followed by a value of 0 to 4, the digit is unchanged. If the last digit of the result that will be printed or printed / displayed ...