Assessments - 3, GPA: 4
(
)
)
|
Facilidade de uso
3. Remote On/Off Button - The button on the top left (see A) is the on/off power button. When pressing this button you will hear a beep, this will activates the power to the fireplace. You must then press the display button (C) to activate the lights. Note: If the flame does not come on immediately, adjust brightness and intensity (buttons E & K). 4. To increase the brightness, press and release the light brighten button (see E). Each time you press this button you will hear a beep, and the brightness will increase slightly until the maximum brightness is achieved. To decrease the brightness, press and release the light dimming button (see D). Each time you press this button you will hear a beep, and the brightness will decrease slightly until the minimum brightness is achieved. 5. Heater Button - To activate the heater, press the heater button (see F), then press HI (G), MED (H), or LO (I). The heater is preset to the following temperatures: • HIGH will shut off when room reaches approximately 86° F (30° C). • MED. will shut off when room reaches approximately 75° F (24° C). • LO. (Low) will shut of when room reaches approximately 64° F (18° C). 6. Flame Button - Press the Flame Adjusting Buttons to achieve a higher or lower flame intensity (see J & K). 7. To Increase Flame Brightness press and release the (K) button. Each time you press this button you will hear a beep and the brightness of the flame will increase slightly, until the maximum setting is reached. To Decrease Flame Brightness press and release the (J) button. Each time you press this button you will hear a beep and the brightness of the flame will decrease slightly, until the minimum setting is reached. 8. To turn the electric fireplace off, Press the On/Off button once (A), when you hear the beep the fireplace will be completely off. When you restart your fireplace with the remote control, all settings will restart at the high settings programmed at the factory. You may also simply press the (C) button to turn off the flame and still use the heater. NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. MAINTENANCE This appliance has been designed to provide many years of trouble-free service. The components that will need to be serviced have been kept to a minimum. Periodic dusting of the fi replace is all that should be required. CAUTION Disconnect power before attempting any maintenance or cleaning to reduce the risk of fire, electrical shock or personal injury. WARNING When cleaning the fireplace, the fi replace must be cool. CLEANING THE GLASS ENCLOSURE PANEL (OPTIONAL KIT) Over time the front glass panel may become dirty or dusty. Dust can be removed by lightly rubbing the glass surface with a clean, lint free cloth or paper towel. To remove fingerprints or other marks, use a damp cloth with a good quality household glass cleaner. The front glass panel should be completely dried with a clean, lint free cloth or paper towel. CAUTION Do not use abrasive cleaners on the glass panel. Do not spray liquids directly onto any surface of the fi replace. WARNING An authorized service representative should perform any other servicing. CAUTION Handle glass very carefully to prevent accidental breakage. HEATER/BLOWER REPLACEMENT PROCEDURE 1. Turn off power to the fi replace. 2. Let the fireplace completely cool, if it has been operating. 3. Open the screens (remove glass panel enclosure, if applicable). 4. OPTIONAL: To ensure that the brick panel isn't accidentally scratched, you may wish to remove it before proceeding: Brick Panel Removal Procedure: a. Remove the 2 screws on the front of the grate. Remove Grate (see Figure 8). b. Lift out Log / Ember assembly and set aside. Caution: Be careful not to scratch the fi nish. c. Remove the top brick panel retaining bracket (see Figure 15). Be very careful to hold the bracket when removing the 2 screws to ensure the bracket doesn't fall. d. Remove the left and right side brick panel retaining brackets (see Figure 15). Be very careful to hold the bracket when removing. Remove the bottom screw fi rst to avoid the frame falling down after both screws are removed. TAKE CARE TO HOLD BRICK PANEL IN PLACE TO PREVENT POSSIBLE DAMAGE. Suggestion: Slide the screens toward the middle of the fireplace for easier access to the screws on the sides. Return the screens to the sides before proceeding to instruction e. e. Tip brick panel forward from the top, just enough to clear screens. Carefully remove brick panel from firebox and set aside in a safe place. 5. Remove the screws which secure the heater blower mounting plate using a phillips screwdriver as follows (see Figures 9 & 10): a. While using one hand to hold the handle of the heater/blower assembly (seeFigure 9), remove the 5 screws which secure the mounting plate. Remove the 4 side screws first (2 on each side). Remove the middle screw that is on the top of the handle last. b. Slowly lower the heater/blower assembly and let it rest on the 2 support chains (1 on each si...
Este manual também é adequado para os modelos :Lareiras - MERIT PLUS SERIES MPE-33R (914.54 kb)
Lareiras - MERIT PLUS SERIES MPE-33R (914.54 kb)
Lareiras - MERIT PLUS SERIES MPE-33R (914.54 kb)