Assessments - 3, GPA: 4.3
(
)
)
|
Facilidade de uso
NEW WALL CONSTRUCTION 1. Select a suitable location that is not susceptible to moisture and is away from drapes, furniture and high traffic. NOTE The fireplace insert must be installed on a hard surface. 2. Place the fireplace in the desired location to see how it will look in the room. 3. Mark the desired location on the floor and store the fireplace in a safe, dry and dust free location. 4. Use studs to frame an opening of 775mm wide X 654mm high X 305mm deep. 5. Plan your electrical power supply. (refer to NOTE 1) Option #1 -The power cord can be lead from behind the trim and along the wall to an outlet near the fireplace. (FIGURE 4) Option #2 -A new outlet can be installed inside the new frame construction. (if allowed by electrical code). (FIGURE 5) FIGURE 5 FIGURE 6 WARNING Construction and Electrical Outlet wiring must comply with local building codes and other applicable regulations to reduce the risk of fire, electrical shock and injury to persons. MANTEL SURROUND KIT OR CUSTOM MADE MANTEL SURROUND 1. Select a suitable location that is not susceptible to moisture and is away from drapes, furniture and high traffic. 2. Place the fireplace in the desired location to see how it will look in the room. 3. For ease of electrical hook up you may wish to locate the fireplace near an existing outlet. (refer to NOTE 1) 4. Store the fireplace in a safe dry and dust free location. 5. Assemble the mantel surround kit (refer to the mantel assembly instructions) or construct the custom surround with an opening of 775mm X 654mm X 305mm. WARNING Do not attempt to wire your own new outlets or circuits. To reduce the risk of fire, electric shock or injury to persons, always use a licensed electrician. FIREPLACE INSERT INSTALLATION This section provides easy step by step instructions for installation of your fireplace. 1. Install Trim Kit to front of fireplace by positioning trim then pushing straight forward against the fireplace. 2. Make sure the unit is switched OFF (Refer to operating instruction section). 3. Plug the fireplace into a 13AMP/230Volt (240V in Australia) outlet. If the cord does not reach you may use a 3-core type extension cord rated for a minimum of 13 AMPS. 4. Push the Fireplace into place so that the trim is against the finished Mantel Surround or wall FIGURE 7 surface. (FIGURE 6) 5. Level, if required with wood shims (not included) (FIGURE 7). WARNING Ensure the power cord is not installed so that it is pinched or against a sharp edge and ensure that the power cord is stored or secured to avoid tripping or snagging to reduce the risk of fire, electric shock or injury to persons. FIGURE 8 OPERATION This section will explain the function of each convenient control. 1. To access the controls, open the upper grill by pulling, near the top right hand side, forward and down. (FIGURE 9) 2. To locate controls refer to FIGURE 10. 3. To conceal the controls during the operation, return the grill to its original upright position. FIGURE 9 WARNING The centre and left hand side of the grille will get hot when the heater is operating. Take care to always grasp the grille on the right hand side. CAUTION If you need to continuously reset the heater, unplug the unit and call your local dealer. A. MAIN ON/OFF SWITCH The ON/OFF SWITCH supplies power to all fireplace functions (Heater/Flame). B. MAIN POWER INDICATOR LIGHT The main power indicator light will illuminate, confirming the unit is turned ON. C. FLAME ACTION CONTROL Turn the flame action control knob to adjust the flame speed to the desired level. D. FLAME BRIGHTNESS CONTROL Turn the flame brightness control knob to increase or decrease the brightness of the flame and embers. E. LED INDICATORS Indicates the current function of the fireplace F. MANUAL SELECTION BUTTONS To choose between flame effect setting, flame effect with low heat setting, and flame effect with high heat setting. G. HEATER THERMOSTAT CONTROL To adjust the temperature to your individual requirements, turn the thermostat control clockwise all the way to turn on the heater. When the room reached the desired temperature, turn the thermostat knob counter clockwise until you hear a click. Leave in this position to maintain the room temperature at this setting. For additional heat, turn clockwise until you hear the click again and the heater will turn on. NOTE: The heater may emit a slight, harmless odor when first used. This odor is a normal condition caused by initial heating of internal heater parts and will not occur again. CDB A F E G FIGURE 10 RESETTING THE TEMPERATURE CUTOFF SWITCH This unit is equipped with a thermostat, which controls the temperature of the room. It does this by turning the heater on and off. The heater is protected with a safety device to prevent overheating. Should the heater overheat, an automatic cut out will turn the heater off and it will not come back on without being reset. It can be reset by switching the main ON/OFF SWITCH to OFF and waiting 5 minutes befor...