Assessments - 3, GPA: 4.3
(
)
)
|
Facilidade de uso
1 ea. Surround Kit 1 ea. Surround Trim Kit 1 ea. Face Kit 1 ea. Instruction Sheet GENERAL INfORMATION All of these parts may scratch and bend, great care should be used in handling them. If you encounter any problems, need clarification of these instructions or are not qualified to properly install this kit, contact you local distributor or dealer. Read this instruction sheet in its entirety before beginning the installa face / Surround Panel Kits (Required) -Includes Black face, Surround, and Black Trim Cat. No. Model Description H7016 SDVI-A-BKN Arched Black Nickel face, Surround (27" x 39"), and Black Trim H7015 SDVI-A-BRN Arched Brushed Nickel face, Surround (27" x 39"), and Black Trim H7014 SDVI-A-B Arched Black face, Surround (27" x 39"), and Black Trim Arched face Surround Figure 1 Arched face TOOLS NEEDED: Flat Bladed Screwdriver tion. ALL wARNINGS AND PRECAUTIONS IN THE INSTALLATION AND OPERATION MANUAL PROVIDED wITH THE APPLIANCE APPLY TO THESE INSTRUCTIONS. TURN Off THE fIREPLACE AND ALLOw IT TO COMPLETELY COOL BEfORE PROCEEDING. IMPORTANT If you have a gold or nickel face kit, be sure to clean it with a soft cloth and household glass cleaner prior to burning the insert. fingerprints left on the plated surfaces while burning will usually remain on the finish permanently. INSTALLATION INSTRUCTIONS Surround Panels Installation TheSDVIinsertsurround panelsare madeof heavygage steelfordurability and, if desired, for the ease of making an inside fit in the fireplace. Step 1. Remove the speed nuts from the parts bag, supplied with the insert (A in Figure 2) and install (with the flat surface forward) on the six holes in the surround brackets - three on each side of the insert (B in Figure 2). A flat bladed screwdriver may help in installing the nuts. NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE. Printed in U.S.A. © 2008 LHP P/N 506033-03 Rev. NC 03/2008 Lennox reserves the right to make changes at any time, without notice, in design, materials, specifications, prices and also to discontinue colors, styles and products. Consult your local distributor for fireplace code information. LHP 1110 West Taft Avenue • Orange, CA 92865 Step 8. Remove the face from the box (see Figure 3) and place the face down making sure that the side with the studs are facing upwards. Be sure that the front of the face is lying on a soft non-abrasive surface. Step 9. The sight obstructor is installed with the curved edge down and the bent edge towards the insert. Slide the tabs on the obstructor into the slots (D in Figure 2) in the surround brackets. Step 10.Install the face onto the surround brackets at position C (shown in Figure 2) and per the instructions in Figure 3. Step 2. Install all surround panels and trim with the insert positioned in Arched Face Installation the fireplace but a few inches in front of its final location. Step 3. Install the side surround panels by lining up the holes in the tabs on the side surround panels in front of the holes on the surround brackets. Next insert two slotted 1/4" truss screws for each side surround panel and secure loosely. Step 4. Fasten top surround panel with the remaining two truss screws. Tighten all six truss screws after adjusting the surround panels to eliminate space between side and top surround panels. Step 5. Assemble the surround trim by inserting the elbowed retainer in the rectangular slot in the ends of the longest piece of trim and secure by tightening the screw in the retainer. Slide the mitred ends of the two side trim pieces onto the elbowed retainer and secure by tightening the retainer screw. Step 6. The fastened trim pieces should now be horseshoe shaped. Slide the trim down over the surround panels so the edge of the surround panel fits just behind the rounded edge of the trim. Step 7. Install three spring clips (found in parts bag in firebox) in each piece of trim by inserting them between the rear of the surround panel and the channel of the trim. The spring clips will push the trim tight to the surround panel. NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE. A C Figure 2 B A = Speed nuts B = Holes in the surround brackets - three on each side C = Location where hooked brackets on face will hang D = Slots in the bracket that the sight obstructor goes into The face has two hooks on each side that slide over and hang on the surround brackets at position C shown here. The face can slide slightly from side to side to center the face on the glass. D Sight Obstructor (D) The face has two hooks on each side that slide over and hang on the surround brackets at position C shown in Figure 2. The face can slide slightly from side to side to center the face on the glass. Figure 3 The hooked brackets identified here will hang on the surround brackets at position C shown in Figure 2 ...