Assessments - 1, GPA: 5
(
)
)
|
Facilidade de uso
A. This appliance is equipped with an ignition device which automatically lights the pilot. Do not try to light the pilot by hand. B. BEFORE LIGHTING smell all around the appliance area for gas. Be sure to smell next to the floor because some gas is heavier than air and will settle on the floor. WHAT TO DO IF YOU SMELL GAS • Do not try to light any appliance. • Do not touch any electric switch. • Do not use any phone in your building. • Immediately call your gas supplier from a neighbor.s phone. Follow the gas supplier.s instructions. • If you cannot reach your gas supplier, call the firedepartment. C. Do not use this appliance if any part has been under water. Immediately call a qualified service technician to inspect the appliance and to replace any part of the control system and any gas control which has been under water. NOTICE: During initial operation of new heater, burning logs will give off a paper-burning smell. Orange flame will also be present. Open damper or window to vent smell. This will only last a few hours. 1. STOP! Read the safety information, column 1. 2. Turn off all electric power to the appliance. 3. Turn wall switch to the OFF position. 4. Open lower louver panel. 5. Turn equipment shutoff valve clockwise to the OFF position (see Figure 42). Do not force. 6. Wait five (5) minutes to clear out any gas. Then smell forgas, including near the floor. If you smell gas, STOP! Follow “B” in the safety information in column 1. If you don.t smell gas, go to the next step. 7. Turn equipment shutoff valve counterclockwise to the ON position. Do not force. 8. Close lower louver panel. 9. Turn on all electric power to the appliance. 10. Turn the wall switch to the ON position. 11. Visually locate the pilot. The ignitor should begin to spark andthe main burner should ignite once flame appears at pilot. • If lighting the appliance for the first time each season, it may take several attempts before the supply gas can reach the pilot and main burners. • If the appliance will not stay lit after several attempts, follow the instructions To Turn Off Gas To Appliance, page 24 and call your service technician or gas supplier. Pilot Equipment Adjustment Shutoff Valve Screw Figure 42 -Turning Equipment Shutoff Valve to the OFF Position 116238-01C 24 OPERATING FIREPLACE To Turn Off Gas To Appliance Optional Remote Operation Operating Optional Blower Accessory INSPECTING BURNERS Pilot Assembly Burner Flame Pattern OPERATING FIREPLACE Continued TO TURN OFF GAS TO APPLIANCE 1. Turn off the wall switch. 2. Turn off all electric power to the appliance if service is to be performed. 3. Open lower louver panel. 4. Remove front hearth brick and control access panel. 5. Turn equipment shutoff valve clockwise to OFF. Do not force. 6. Close lower louver panel. Ignitor Sensing Rod Pilot Burner Figure 43 - Pilot OPTIONAL REMOTE OPERATION Note: The WRC receiver and hand-held remote control kit must be purchased separately (see Accessories, page 34). Follow installation instructions on page 22. 1. TurnequipmentshutoffvalvetoONposition.Youcannowturn the burner on and off with the hand-held remote control unit. IMPORTANT: Be sure to press the ON/OFF buttons on the hand-held remote control unit for up to 3 seconds to assure proper operation. 2. Press the ON/OFF button to turn the burner on and off. OPERATING OPTIONAL BLOWER ACCESSORY Locate the blower controls by opening the lower louver panel on the fireplace. Blower controls are located on the left side of the switch bracket to the right just inside the louver panel. TheBKmanualblowerandtheBKTthermostatically-controlled blower have an ON setting and an OFF setting. The blowerwill only run when the switch is in the ON position. In the OFFposition, the blower will not operate. Note for BKT Only: If you are using BKT blower with optional thermostat (wall mounted or remote control) for the fireplace, your fireplace and blower will not turn on and off at the same time.Thefireplacemayrunforseveralminutesbeforetheblowerturns on. After the heater modulates to the pilot position, the blower will continue to run. The blower will shut off after the firebox temperature decreases. The blower helps distribute heated air from the fireplace. Periodically check the louvers of the firebox and remove any dust, dirt or other obstructions that will hinder the flow of air. INSPECTING BURNERS Check pilot flame pattern and burner flame patterns often. PILOT ASSEMBLY The pilot assembly is factory preset for the proper flame. Alterations may have occurred during shipping and handling. The pilot is located on the left hand side of the burner. The flame must envelope 1/4" of top of the ignitor/sensor and grounding stem. If your pilot assembly does not meet these requirements: • Turn the adjustment screw marked PILOT clockwise to decrease or counterclockwise to increase the flame to proper size (see Figure 42, page 23). Do not remove the adjustment screw. • see Troubleshooting, page 26 S...