Assessments - 2, GPA: 4.5
(
)
)
|
Facilidade de uso
Rest bottom edge of panel on back edge of grate (see Figure 38). 6. Install top brick panel by resting on the top of the rear panel. Hold the top brick panel in place and install left side brick panel by sliding it between the grate and the side of the firebox, securing top panel (see Figure 39). 7. Install the right brick panel using the same method described in step 6 for left brick panel. 8. Replace deflector shield using screws removed in step 4. FIREPLACE INSTALLATION Continued FIREPLACE INSTALLATION Installing Optional Brick Liner Models BL36D(S), BL36DH(S), BL42D(S), BL42DH(S) 108862-01D Forr morre iinfforrmattiion,, viisiitt 2233 FIREPLACE INSTALLATION Continued FIREPLACE INSTALLATION Installing Logs, Lava Rock, and Glowing Embers Figure 41- Installing Log No. 2 2 Figure 42 - Installing Log No. 3 3 2. Rest left side of log #2 (front log) onto top of log #1. Place right side of log onto second pin located on right side of grate (see Figure 41). 3. Place log #3 (rear log) onto pins on rear of grate as shown in Figure 42. 4. Place log #4 (crossover log) onto pins from both logs #2 and #3 as shown in Figure 43. 5. Place log #5 (top log) onto right pin of front log (#2) and the smooth surface of crossover log (#4) as shown in Figure 44. Make sure it is seated properly. 6. Place log #6 (left log) onto left pin of front log (#2) and the smooth surface of rear log (#3) as shown in Figure 45. Make sure it is seated properly. 7. For (V)V42 series only, place log #7 onto right pin of top log (#5) as shown in Figure 45. Make sure it is seated properly 8. Place lava rock along sides and front of firebox bottom in areas that are visible only. It is not necessary to use all of the lava rock provided. NOTICE: Do not put lava rock on burner or under burner. Placing lava rock on burner will cause performance problems. 9. Pull ember material apart into pieces no larger than a dime. Place these pieces loosely and sparingly directly onto the exposed section of the front burner and along the space between the burner and grate prongs (see Figure 46). This will create the glowing ember appearance as the flame touches the ember material. Do not block air slots by using too much ember material in one area. It is not necessary to use all of the ember material provided. 10. Close glass door, lock door latches, replace screen, and close louvers (see Removing/Replacing Glass Door, steps 5 through 7, page 21). WARNING: The glass door must be securely in place before running this fireplace. Do not run this fireplace if glass is missing or broken. Ember Material Figure 46 - Placing Ember Material on Burner Figure 44 - Installing Log No. 5 5 6 7 Figure 45 - Installing Log No. 6 (36" and 42" Series) and Log No. 7 (42" Series Only) 42" Series Only Figure 43 - Installing Log No. 4 4 108862-01D Forr morre iinfforrmattiion,, viisiitt 24 OPTIONAL REMOTE CONTROL INSTALLATION (Model WRC) Note: If using optional wireless hand-held remote control, the wall switch must be in the ON position to be operational. The remote control then becomes the switching mechanism for fireplace operation. 1. Open lower louver panel. 2. The WRC model receiver does not require a battery. The receiver can be installed by first plugging the short extension cord into the fireplace receptacle. Then plug the receiver unit into the extension cord. Finally plug the ignition module plug into the receiver unit (see Figure 47). 3. Activate the remote handset battery by removing the insulating tab on the back of the handset (see Figure 48). The battery is included pre-installed. 4. Once the battery is activated the unit is ready to use. 5. Close lower louver panel. Figure 47 - Installing the WRC Remote Receiver Fireplace Receptacle Remote Control Receiver Extension Cord Ignition Module Plug Figure 48 - Installing Battery into Back of Handset Pull to Remove Insulation Tab Battery Cover 12 Volt Battery Back of Handset Robertshaw MODEL SP745 IGNITION CONTROL STEP DOWN TRANSFORMER MV TH PV/MV TR GND PV IGN EV2 INCOMING MAIN GAS SUPPLY EV1 GAS LINE TO BURNER 24V AC 120V AC INCOMING 120V AC (FUSE BOX OR BREAKER) OFF ON (SUPPLIED) WALL SWITCH GREEN BLACK WHITE 120v, 60Hz, 0.7A ELECTRICAL RATING: BLACK WHITE GREEN OPTIONAL REMOTE CONTROL WIRING DIAGRAM Pilot Burner Pilot Gas Line WALL SWITCH INSTALLATION The installation of a wall switch allows you to activate the gas control valve and turn the fireplace on and off. The wall switch is to be connected to the incoming 120 volt regular household wiring that supplies the electricity to the fireplace. Refer to wiring diagram below. FIREPLACE INSTALLATION Wall Switch Installation Optional Remote Control Installation WIRING DIAGRAM FIREPLACE INSTALLATION Continued OPERATING FIREPLACE For Your Safety Read Before Lighting Lighting Instructions To Turn Off Gas To Appliance Optional Remote Operation 25 OPERATING FIREPLACE FOR YOUR SAFETY READ BEFORE LIGHTING WARNING: If you do not follow these instruct...
Este manual também é adequado para os modelos :Lareiras - (V)V42EP (4.73 mb)
Lareiras - (V)V42EN (4.73 mb)