Assessments - 2, GPA: 4
(
)
)
|
Facilidade de uso
1 Attach Bowl Assembly B x 4 2 Attach LP Gas Tank Shield B x 4 6 Attach Base B x 18 5 Attach Side Panels, Right Front Leg and Middle Support Leg A x 2 B x 12 Assembly Instructions (continued) 10 Attach Doors C x 2 9 Attach Base Support Bar B x 2 11 Place Wood Grid and Lava Rocks Place Cement Logs 12 Insert Battery E x 1 Operating Instructions Installing LP Gas Tank To operate you will need (1) precision-filled standard grill LP gas tank (20#) with external valve threads. Note: An empty standard grill LP gas tank weighs approximately 18 lbs. A precision-filled standard grill LP gas tank should weigh no more than 38 lbs. Need a tank of gas? Try tank exchange service. It’s easy, fast, safe, and available at tens of thousands of conveniently located retail outlets nationwide. You can purchase a new full tank or exchange your empty for a precision filled one. Insert LP Gas Tank WARNING: Make sure LP gas tank valve is closed. Close by turning valve clockwise. Place precision filled LP gas tank upright into hole in outdoor fireplace body so it is arranged for vapor withdrawal. Secure LP Gas Tank Secure tank by sliding tank retainer chain around the LP gas tank and insert peg into LP gas tank tray. Note: Peg must be inserted into LP gas tank when tank is in LP gas tank tray. Connect LP Gas Tank Before connecting, be sure that there is no debris caught in the head of the LP gas tank, head of the regulator valve or in the head of the burner and burner ports. Connect gas line to tank by turning knob clockwise until it stops. Disconnect LP Gas Tank Before disconnecting make sure the LP gas tank valve is OFF. Disconnect gas line to tank by turning knob counterclockwise until it is loose. Checking for Leaks WARNING: Before using this outdoor fireplace, make sure you have read, understand and are following all information provided in the Dangers and Warnings presented on page 2. Failure to follow those instructions can cause death, serious injury or property damage. Burner Connections Make sure the regulator valve and hose connections are securely fastened to the burner and the tank. If your unit was assembled for you, visually check the connection between the burner pipe and orifice. Make sure the burner pipe fits over the orifice. WARNING: Failure to inspect this connection or follow these instructions could cause a fire or an explosion which can cause death, serious bodily injury, or damage to property. Please refer to diagram for proper installation. If the burner pipe does not rest flush to the orifice, please contact 1.800.762.1142 for assistance. Tank/Gas Line Connection Make 2-3 oz. of leak solution by mixing one part liquid dishwashing soap with three parts water. Make sure control knob is OFF. Turn LP gas tank ON at valve. Spoon leak check solution at all “x” locations If any bubbles appear turn LP gas tank OFF, reconnect and re-test. If you continue to see bubbles after several attempts, disconnect LP gas source and contact 1.800.762.1142 for assistance. If no bubbles appear after one minute turn tank OFF, wipe away solution and proceed. Lighting 1. Make sure there are no obstructions of airflow to the gas unit. Spiders and insects can nest within and clog the burner / venturi tube at the orifice. A clogged burner tube can lead to a fire beneath the appliance. 2. Control knob must be in the “OFF” position. 3. Turn on gas at LP gas tank. 4. Push and turn control knob counterclockwise to “LOW”. 5. Press the electronic igniter and hold for 5 seconds to light burner. 6. Release control knob after 45 seconds. 7. If ignition does not occur in 45 seconds, turn burner control knob “OFF”, wait 5 minutes, fan with newspaper or magazine, and repeat lighting procedure. 8. If igniter does not light burner, use a long match or long butane lighter. CAUTION: Before Lighting - Using a shovel to carefully move the lava rocks to access the burner. a. Wearing Heat reistant gloves, position the lit long match or lit long butane lighter near the side of the burner. b. Turn control knob counterclockwise to “LOW”. c. Remove long match/long butane lighter. CAUTION: After Lighting - Using a shovel and heat resistant gloves, carefully move the lava rocks back to their proper position, being careful to avoid the flame. LP Gas Connection LP Gas Valve with Orifice Burners XXXXX LP Gas Tank Valve Control Knob K Lighting Rod Placement Proper flame height. 9. After lighting, observe the burner flame, make sure all burner ports are lit and flame height matches illustration. 10. Adjust flame to desired flame with the control knob. CAUTION: If burner flame goes out during operation, immediately turn the gas “OFF” and let the gas clear and fan with newspaper or magazine for about 5 minutes before re-lighting. Turning Off 1. Turn gas off at LP tank. 2. Turn all control knobs clockwise to the OFF position. Cleaning and Care Inspecting This outdoor fireplace should be inspected on a regular basis to ensure product safety and longer product life. WARN...