Assessments - 4, GPA: 4
(
)
)
|
Facilidade de uso
Continued UNVENTED (VENT-FREE) FIREBOX INSTALLATION Continued INSTALLING BLOWER ACCESSORY (MODEL CGFB32C ONLY) You may install blower accessory GA3750 with conventional installation (below) or with built-in installation (page 10) with model CGFB32C only. To install blower accessory, see instruction sheet included with the kit. Conventional Installation of Blower Accessory 1. Install blower assembly per instruction sheet included in blower accessory kit. 2. Before replacing bottom of firebox, route blower power cord through hole in support bracket in bottom of firebox and through hole in side of firebox to grounded, three-prong 120 volt electrical outlet (see Figure 8). Plug electrical cord into outlet. 3. Replace bottom of firebox. NOTICE: A certified electrician must connect electrical wiring to duplex outlet for built-in installa tion. Follow all local codes. In absence of local codes, follow the National Electrical Code, ANS/ NFPA 70 (Latest Edition). Electrical Outlet Side Opening Support Bracket Opening Slower Power Cord Figure 8 -Routing Blower Accessory Power Cord for Conventional Installation Built-In Installation of Blower Accessory 1. Install blower assembly per instruction sheet included. 2. Before replacing bottom of firebox, remove screw holding duplex outlet to the support bracket in the bottom of firebox, Remove duplex outlet. 3. Clamp electrical cable into firebox through smallest hole using strain relief provided. 4. Route wires from electrical box through hole in side of heater and hole in support bracket (see Figure 9). 5. Connect wires from the electrical box to duplex outlet. Match wire colors to those indicated on duplex outlet. Be sure to connect ground wire. 6. Replace duplex outlet with screw. 7. Plug blower power cord into duplex outlet. 8. Replace bottom of firebox. Cables From Electrical Source Duplex Outlet Screw SlowerPower Cord Figure 9 -Routing Blower AccessoryPower Cord for Built-In Installation INSTALLING LOG HEATER IN FIREBOX _]k CAUTION: Do not pick up log base assembly by burners, This could damage burners. Only handle base by grates. _k CAUTION: Do not remove the metal data plates attached to the heater base assembly. The data plates contain Important warranty Information. 1. Remove four screws holding firebox bottom in place. 2. Lift and remove firebox bottom (see Figure 10). 3. If installing GA3750 Blower Accessory (Model CGFB32C only), see Installing Blower Accessory. 4. Route flexible gas line from manual shutoff valve into firebox through side. NOTICE: Most building cedes do not permit concealed gas connections. A flexible gas line is recommended to allow accessibility from the firebox. The flexible gas supply line connection to the manual shutoff valve should be accessible, 5. Attach gas log heater base to firebox bottom with four screws included with base (see lnstallihg Heater Base Assembly in log set owner's manual). 6. Replace firebox bottom and secure with screws. B Figure 10-Removing Firebox Bottom 8 1o3573 OWNER'S MANUAL INSTALLATION Continued INSTALLING FIREPLACE SCREEN 1. Insert each rod through nine rings located at top of screen. 2. Insert first rod into rear hole in left side of firebox. Fasten rod to rear hole near center of firebox using black shoulder screw. 3. Insert other rod into front hole on right side of firebox and fasten using remaining shoulder screw. Rear Hole Screw Figure 12-Installing Fireplace Screen FIREBOX INSTALLATION USING OPTIONAL ACCESSORY MANTELS This firebox may be installed using the cabinet mantel andhearthbase accessories against a wall in your home. Follow the instructions below m install the firebox in this manner. Note:Theinstructions below show installa tion using GMCIlF/GMCI2U/GMC13F series cabinet mantels and the GC3333F/ "GC3334U/GC3335F series hearth base accessories. The hearth base accessory shown is optional for this installation. You can install firebox and cabinet mantel directly on the floor. 1. Assemble cabinet mantel, hearth base, and perimeter trim (Included with mantel). Assembly instructions are included with each accessory, 2. If using an optional GA3750 blower (CGFB32C model only), install a properly grounded, 120 volt three-prong electrical outlet at firebox location if an outlet is not there. If possible, locate outlet so cabinet mantel will cover it when installed (see Figure 14). 3. Install gas piping tofirebox location. This installation includes an approved flexible gas line (if allowed by local codes) and a manual shutoff valve. The flexible gas line must be the last item installed on the gas piping. See Connecting to Gas Supply in your log set owner's manual. NOTICE: A qualified service person must connect firebox to gas supply. Follow all local codes. 4+ Place hearth base accessory against wall at installation location. Cut an access hole in hearth top to run flexible gas line to firebox (see Figure 13). Make sure to locate access hole so cabinet mantel will cover it when installed. Note: You can...
Este manual também é adequado para os modelos :Lareiras - CGFB32C (679.49 kb)