Assessments - 3, GPA: 3.3
(
)
)
|
Facilidade de uso
Take out all the parts and compare them to the diagrams below. Be sure you have all the parts and can identify them. • A helping hand is always good: assemble your mantel with an adult assistant if possible. Some pieces are heavy and will need to be held by a helper. Assembly time will be approximately 30-60 minutes. • Locate a good Phillips-head screwdriver. You may also use an electric screwdriver but be careful not to strip the head of the screw by over tightening them. • After you assemble your mantel, if you find you have interference between the door and the hearth please see Step 6 of these installation instructions for the solution. NOTE: 284SOK = Oak Finish, 284SCH = Cherry Finish TOP 1PC 284SOK.14/284SCH.14 LEFT SIDE PANEL RIGHT SIDE PANEL LEFT SIDE PANEL BASE 1PC (EXTERIOR) 1PC (EXTERIOR) 1PC (INTERIOR) 1PC 284SOK.01/284SCH.01 284SOK.02/284SCH.02 284SOK.03/284SCH.03 284SOK.03/284SCH.03 TOP SHELF 2PCS BASE SHELF 2PCS CENTER PANEL 1PC FIREBOX SHELF 1PCLOWER CENTER RIGHT SIDE PANEL 284SOK.06/284SCH.06 284SOK.07/284SCH.07 284SOK.09/284SCH.09 PANEL 1PC 284SOK.11/284SCH.11 (INTERIOR) 1PC 284SOK.10/284SCH.10 284SOK.05/284SCH.05 BACK PANEL 2PCS 284SOK.08/ 284SCH.08 LEFT DOOR 1PC 284SOK.12/ 284SCH.12 RIGHT DOOR 1PC 284SOK.13/ 284SCH.13 1 1 4 4 SHELF 8PCS 284SOK.15/284SCH.15 ANTI-TIP DEVICE 2 SETS GET READY TO START Before assembly, use scissors to unwrap the parts from the packaging. DO NOT use a box cutter or exacto-knife as you may cut into the mantel pieces inside the box and damage the finish. Check for the hardware bag which is red and located inside the packaging taped to the top box. Be sure you DO NOT discard any pieces. Step 1 Locate the hearth and place it on the floor. Do not put it up against the wall at this point in the assembly as you need to get in behind the mantel to insert several screws. Step 2 Locate the 2 base shelves. Standing in front of the hearth, place them with the finished side up on the bottom of the left and right side hidden storage compartments. Step 3 Locate the left inside and left outside wall panels, the back panel and the top panel for the left hidden storage compartment. Locate the bag of plastic shelf supports. Insert 8 supports into the holes on the inside of both the inside and outside wall panels. NOTE: It is much easier to do this step before you have built the hidden storage compartments. Now position both the inside and outside wall panels so that the bottom fits underneath the base shelf. Slide the back panel (finished side inside the compartment) between the side panels ensuring that the back panel stays in position within the grooves on both side panels. Get your helper to hold the panels snuggly in place while you insert the 6 bottom screws which will hold the sides and back in position. Position the top shelf in place. Ensure the compartment back is fitted into the groove on the top shelf. Get your helper to apply pressure to the side to eliminate any gaps while you insert and tighten the top 6 screws. You are now ready to insert the 4 shelves onto the shelf supports to complete the storage compartment. Step 4 Repeat Step 3, but with the right inside and right outside wall panels. Step 5 Locate the center panel that will be attached to the left and right storage compartments and will sit above the firebox. Position it with the finished side facing the front of the mantel. Insert and tighten the 4 screws which will hold the center panel in place. Locate the lower center panel and place it on the hearth with the finished side facing the front. Insert the 2 screws which will hold it into place. CAUTION DO NOT USE AN ELECTRIC DRILL TO INSERT THESE SCREWS. A POWER DRILL CAN DRIVE THE SCREWS THROUGH THE FACE OF THIS PANEL THIS SHOULD NOT HAPPEN WITH A MANUAL SCREWDRIVER. BE CAREFUL.. Step 6 Place the firebox shelf between the storage compartments and slide it into position so that it sits flush with the lower center panel. Step 7 You are now ready to install the doors on the right and left side storage compartments. Locate the left door. The hinge bracket for this door is already attached to the hinge located inside the left compartment (it came installed). Get your helper to hold the door in position while you insert and tighten the 2 screws in each of the hinges. Repeat for the right side door. You can level the doors by releasing or tightening the tension on the leveling screw on each hinge (see picture for location) and realigning the door so it is level from the front. Leveling screws Step 8 Get your helper and locate the top of your mantel. This top is very heavy. It will take 2 people to lift and position it in place. Ensure the top goes over the positioning guide located on the header. The top must go over this guide to be positioned correctly. Once the top is in place insert and tighten the 6 screws. Step 9 Take your electric firebox out of its packaging and position it between the 2 legs of the mantel. The...
Este manual também é adequado para os modelos :Lareiras - Muskoka MM284SCH (571.39 kb)